User Account

All Pages

Find the voltage necessary at feed point

Assignment Help Electrical Engineering
Reference no: EM131202858

1. A 250 m, 2 wire D.C. distributor fed from one end is located uniformly at the rate of 1.6 A/metre. The resistance of each conductor is 0.0002 ohms per metre. Find the voltage necessary at feed point to maintain 250 V

i). At the far end

ii). At the mid-point of the distributor

2). Derive an expression for the power loss in a unifoimly loaded distributor fed at one end.

Reference no: EM131202858

Questions Cloud

Etermine the capacitance and resistance values of the filter : Design a high-pass op amp filter with a high-frequency gain of- 100 and a cutoff frequency of 1 kHz. Resistors with values of 1 kΩ, 10 kΩ, and 100 kΩ are available. Determine the capacitance and resistance values of the filter.
Discuss the big five personality test : Describe the differences between dispositional and evolutionary or biological personality theories. Discuss the strengths and limitations of dispositional and evolutionary or biological personality theories as they apply to behavior.
Determine the remaining parameters : An op amp low-pass filter is to have a cutoff frequency of 100 Hz and a gain of magnitude 50. Determine the remaining parameters if the capacitor is specified as C= 1 µF.
Explain the impact or benefit that was produced : Describe examples of organizational citizenship behavior that you have witnessed in the workplace. Explain the impact or benefit that was produced.
Find the voltage necessary at feed point : Find the voltage necessary at feed point to maintain 250 V At the far end. - Derive an expression for the power loss in a unifoimly loaded distributor fed at one end.
How schizophrenia relates to genetics or brain chemistry : Contrast the positive and negative symptoms of schizophrenia and explain why it is thought these different symptoms might have a different physiological foundation.
What is the cost of waste due to excess inventory : Ann Kyser, a teacher at Hewitt Middle School, is in charge of ordering the T-shirts to be sold for the school’s annual fund-raising project. The T-shirts are printed with a special Hewitt School logo.  If the school receives actual sales orders for 7..
Design a 2-to-4 decoder with enable input : The selected output is equal to 0 (while all other outputs are equal to 1).
Calculate the sag from the taller of the two supports : Calculate the sag from the taller of the two supports which must be allowed so that the factor of safety shall be 5.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Find logic ckt to form part of automobile safety arrangement

Design a logic circuit to form part of automobile safety arrangement, providing a warning light, consisting of an LED, if (a) whenever the door is open or (b) when the seat belt is not buckled and the key is in the ignition.

  Calculate the apparent power and the power factor

If it has a resistance of 30 Ω and an inductance of 0.5 H, calculate the apparent power and the power factor.

  Calculate the internal resistance of the battery at the load

A standard D cell flashlight battery is connected to a load of 3 Ω. After 6 hr of intermittent use the load voltage drops from an initial 1.5 V to a final useful voltage of 0.9 V.

  Deduce equation of total transference for a feedback system

Deduce the equation of the total transference for a feedback system with an operator of gain a, and a feedback network of transfer β.

  Compute the bit error probability for both constellations

2. Compute the symbol error probability for both constellations in terms of the Gaussian error integral Q(x). 3. Compute the bit error probability for both constellations in terms of the Gaussian error integral.

  Compare a lumped element model of a lossless transmission

Compare a lumped element model of a lossless transmission line (single L and C) with the distributed model. Use the following values for the transmission line in this comparative analysis.

  Porter five competitive forces

Porter's Five Competitive Forces

  Calculate the impedance of inductor circuit in polar form

An inductor rated at 4 Henrys is subjected to a sinusoidal AC voltage of 24 volts RMS, at a frequency of 60 hertza) Write the formula for calculating inductive reactance (XL), and solve for current through the inductor.

  Find the output voltage produced

A 6-bit DAC has an input of 1001012 and uses a 10.0-V reference. a. Find the output voltage produced. b. Specify the conversion resolution.

  Estimate the minimum and maximum values of k

Estimate the minimum and maximum values of Ko over the voltage tuning range - For the voltage controlled oscillator (VCO) in the system, the V-f measurements in the table were obtained.

  Find the critical path and determine the propagation delay

Design the combinational 3 bit gray to binary code converter for conversion angular position of a shaft into binary code. 1) Complete the truth table 2)obtain the minimal solution with a K map 3) draw the circuit diagram, labels the inputs and output..

  Describe the impact and the vulnerability of the scada

Describe the impact and the vulnerability of the SCADA

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd