Find the voltage level of that signal

Assignment Help Electrical Engineering
Reference no: EM131257018

A digital-to-analog converter uses a reference voltage of 120 V de and has eight binary-digit precision. In one of the sampling instants, the data contained in the binary register 01010101. If a zero-order hold is used to generate the output signal, determine the voltage level of that signal.

Reference no: EM131257018

Questions Cloud

Find the appropriate hourly rate for this work cell : The work cell will operate 2000hr/yr. Use a rate of return uf25% to determine the appropriate hourly rate for this work cell.
What is the appropriate goal for the inflation rate : What is the appropriate goal for the inflation rate? How should the Federal Reserve Board use its policy to achieve its goals? How effective is the Federal Reserve monetary policy in achieving its goals?
Discuss implications of personality type leadership ability : Use the results of your Psychodynamic Survey and James Barraclough's presentation on MBTI Preference and Awareness to describe your personality type. Use your involvement in your CAP group to discuss the implications of your personality type on y..
Addresses the role of the brain and nervous system : Write a paper of 1,000-1,250 words that addresses the role of the brain, nervous system, sensory systems, and cognitive functions in shaping behavior. Include the following in your paper: A discussion of the role of the brain, nervous system, and s..
Find the voltage level of that signal : If a zero-order hold is used to generate the output signal, determine the voltage level of that signal.
Develop your request for proposal based on discussion board : You will also develop your request for proposal (RFP) based on Discussion Board. Prepare a table of the evaluation criteria that you will use to select your top vendor.
Determine the equation for the voltage : A DAC uses a reference voltage of 80 V and has 6-bit precision. In four successive sampling periods each 1 sec long. the binary data contained in the output register were 100000, 011111, 011101, and 011010.
Probability that the project will be completed in 17 months : What is the probability that the project will be completed in 17 months? - What is the probability that the project will be completed in 20 months?
Microchip technologies eliminates : Sales Commissions Mitch Little started to question the conventional wisdom on sales commissions in the late 1990s, shortly after he became vice president for worldwide sales and applications at Microchip Technologies, a large semiconductor compan..

Reviews

Write a Review

Electrical Engineering Questions & Answers

  What is the increment between the voltages

A flash type 5 bit ADC has a reference voltage of 10v.- what is the increment between the voltages applied to the comparators.

  What is role of miller in high frequency amplifier design

1. What is Miller capacitance What is its role in High frequency amplifier design Label all the involved variables in the Figure below and derive an expression for the Miller effect capacitances (input and output).

  Show the output of adc

An 8 bit unipolar Successive Approximation Register type ADC is used to convert 3.5V to digital equal output. The reference voltage is +5V - The output of ADC at end of 3rd clock pulse after the start of conversion

  Determine the mesh current i1

Consider the circuit shown in the figure below. Suppose that R1 = 6Ω , R2 = 13Ω and R3 = 17Ω. Determine the mesh current i1. Express your answer to three significant figures and include the appropriate units.

  How to determine the line current at starting

A 3-phase cage rotor induction motor has a full load slip at 5% . The standstill current at rated voltage is 6.5 times full load current . Find autotransformer tapping to give full load torque at starting and also find the line current at starting..

  Rc circuit with zero initial condition

Given the following RC circuit with zero initial condition on the C1 voltage:

  Design full-wave bridge rectifier circuit to deliver 10volts

Design a full-wave bridge rectifier circuit to deliver 10 volts de with less than 0.1 volt (pp) ripple into a load draWing up to 10mA. Choose the appropriate ac input voltage. assuming 0.6 volt diode drops.

  A new semiconductor has nc 1019 cm3 and nv5 x 1018 and

a new semiconductor has nc 1019 cm3 and nv5 x 1018 and eg 2ev. if it is doped with 1017 donors fully ionized

  Determine the unit vector in rectangular components

A circle, centered at the origin with a radius of 2 units, lies in the xy plane. Determine the unit vector in rectangular components that lies int he xy plane, is tangent to thte circle at 3.

  Draw the standard form simulation diagram

How do you draw the standard form simulation diagram given a higher-order differential equation; and how to make adjustments if the output must be put in the state equation form, y=Cx+Du.

  What is the ratio of output current ic to input current ib

Solve for the currents IB, IC, and IE using the fact that VBE = 0.7 V and VCE = 8 V. - Find the voltages VB, VC, and VE with respect to ground.

  Compute length of time required for average

(a) From Figure, compute the length of time required for the average grain diameter to increase from 0.01 to 0.1 mm at 500oC for this brass material. (b) Repeat the calculation at 600°C.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd