Find the velocity of the wind

Assignment Help Mechanical Engineering
Reference no: EM13212703

A plane can fly 299 mph in still air. If it can fly 180 miles downwind in the same amount of time it can fly 119 miles upwind, find the velocity of the wind.

Reference no: EM13212703

Questions Cloud

How deep is the notch : A block of metal has a 90 notch cut from its lower surface. The notched part rests on a circular cylinder of diameter 2.0 cm, as shown in Fig. 4.15. If the lower surface of the par is 1.3 cm above the base plane, how deep is the notch?
Use dcf methodology and reevaluate the buy-out : What changes in the analysis or additional analysis do you suggest before a final decision should be made and sShould Acme make a deal if its policy is to never exceed a 20% premium in any tender offer
Find the stoichiometric air/fuel ratio of benzene : Please find the stoichiometric air/fuel ratio of benzene (C6H6) and the actual air fuel ratio when operated at equivalance ratio of 0.8.
Find the mass of gasoline fuel injected into each cylinder : Please find the mass of gasoline fuel injected into each cylinder in each working cycle.
Find the velocity of the wind : A plane can fly 299 mph in still air. If it can fly 180 miles downwind in the same amount of time it can fly 119 miles upwind, find the velocity of the wind.
Calculate the break hp of the pump using water : Using a centrifugal pump, and a flow rate of 60 gal/min, calculate the break hp of the pump using water with a density of 62.4lbm/ft3 and do the same for a nonviscous liquid having a density of 0.85g/cm3.
What similarities would investors have : A survey of 25 grocery stores revealed that the average price of a gallon of milk was $2.98 with a standard error of $0.10. If 90% and 95% confidence intervals are developed to estimate the true cost of a gallon of milk, what similarities would th..
Calculate the dimensions of the agitation : For the preliminary design a power of 0.5kW/m^3 volume is to be used. Calculate the dimensions of the agitation system, rpm, and kW power.
Explain the composition of stream and the pressure : At the temperature that both stages are operating at, the vapor pressure of A is 10 kPa and the vapor pressure of B is 100 kPa. The liquid and vapor phases leaving each unit are in equilibrium. Find the composition ..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  What is the airspeed of the plane

The airspeed of an aeroplane is measured with a Pitot tube. The plane is flying at an altitude of 10000m, and the Pitot tube measures a gauge pressure of p = 10kPa. What is the airspeed of the plane?

  What is the expected annual cost savings in dollars

A 50 hp motor with an efficiency of 0.80 is to be replaced by a newer model motor with an efficiency of 0.90. The motor is expected to operate 3000 hours per year. The cost of electricity in our area is $0.06 per kWhr.

  Use potential flow theory to determine the lift coefficient

Use potential flow theory to determine the lift coefficient of a spinning baseball in terms of the forward velocity (V ) and spin RPM.

  Determine the actual and minimum theoretical operating

determine the actual and minimum theoretical operating costs, each in $/day.

  Draw and label a schematic of the system

A 10 kW electric heater is used to heat 2 kg of air contained in an insulated rigid tank from 400 kPa  and 50 °C to 200 °C. The ambient air temperature and pressure is 20 °C and 100 kPa, respectively.

  Compute the position of the quasi-fermi

calculate the position of the quasi-Fermi levels for electrons and holes with respect to the intrinsic level (assume that ni=1.5x10^10cm^-3).

  Evaluate the exit velocity

Evaluate the valve closure to achieve a water exit velocity

  Calculate the transverse modulus of the peek

calculate the transverse modulus of the peek/carbon fiber composite with 30% volume fraction by tow method. the modulus of peek is 3.8 GPa and the modulus of the carbon fiber is 400GPa. assume the reinforcing factor.

  Explain modulus of elasticity

A linear isotropic material has the shear modulus of elasticity G of 11.5*10^6 psi and the Poisson's constant v of 0.3.

  Explain piston-cylinder assembly undergoes a constant

Refrigerant R-134a vapor in a piston-cylinder assembly undergoes a constant-pressure process from saturated vapor at 800 kPa to 50 ºC.

  Komodo dragons are the largest lizards known to man

Komodo dragons are the largest lizards known to man. A 250-pound dragon can eat enough food to increase it body weight by 1/2. Which number sentence could be used to find w, the weight of a k0modo dragon after increasing it body weight by 1/2?

  Estimate the schmid factor

Estimate the Schmid Factor, which is used to convert the CRSS into a critical tensile 'yield' stress. Use the measured angle between the slip trace and the sample long axis

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd