Find the velocity of the stream issuing out of the nozzle

Assignment Help Mechanical Engineering
Reference no: EM13631273

Two streams of air, one at 1 bar, 27degree and velocity of 30 m/s and the other at 5 bar, 227 degree and 50 m/s velocity, mix in equal proportion in a chamber from which heat at the rate of 100 kJ/kg is removed. The mixture is then passed through an adiabatic nozzle. Find the velocity of the stream issuing out of the nozzle. The temperature of air leaving the nozzle is 27degree, and its Cp=1.005kj/kg.K

Reference no: EM13631273

Questions Cloud

If a light bulb bought from a particular store has a 18 : if a light bulb bought from a particular store has a 1.8 probability of being defective when it leaves the store
A weight of 300 n is suspended from a spring that has a : a weight of 30.0 n is suspended from a spring that has a force constant of 190 nm. the system is undamped and is
What is refraction how and why does it occur why does : what is refraction? how and why does it occur? why does light change its speed as it passes from one medium to
A 1500 lb crate is pulled along the around at a constant : a 1500 lb crate is pulled along the around at a constant speed for a distance of 25ft using a cable that makes an andle
Find the velocity of the stream issuing out of the nozzle : two streams of air one at 1 bar 27degree and velocity of 30 ms and the other at 5 bar 227 degree and 50 ms velocity mix
Design a process to produce a 05 cm-diameter steel shaft : design a process to produce a 0.5 cm-diameter steel shaft having excellent toughness yet excellent wear and fatigue
Water vapor at 6 mpa 600c enters an adiabatic turbine : water vapor at 6 mpa 600?c enters an adiabatic turbine operating at steady state and expands to 10 kpa. the mass flow
Estimate the spacing between the two irrandiance maxima : estimate the spacing between the two irrandiance maxima closest to the geometric of a plain wave illuminated
Determine the concentration of carbon in an iron-carbon : determine the concentration of carbon in an iron-carbon alloy for which the microstructure consists of proeutectoid

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A the engineer you know that the metallurgical temperature

a heat engine is operating on carnot cycle. the waste heat from this engine is rejected to a nearby lake at 62f at a

  What weight of iron must be tied to one end of the log to

a cylindrical log is 1 ft in diameter and 20 ft long. what weight of iron must be tied to one end of the log to keep it

  A 3000-lb car accelerates under constant power from 60

a 3000-lb car accelerates under constant power from 60 mileh to 90 mileh on a 0.25 mile straight level test track.

  Kerosene having a specific weight of 500 lbft3 is flowing

1. a fire hose nozzle has an orifice diameter of 1inch. according to some fire codes the nozzle must be capable of

  If the cold-air assumptions can be applied determine how

a four cylinder two stroke diesel engine has a cut-off ratio of 1.8 and a compression ratio of 22. it operates with an

  Neglecting the effect of the fillets and of stress

neglecting the effect of the fillets and of stress concentrations determine the smallest permissible diameters of the

  Calculate the max deflection in a titanium alloy cantilever

calculate the max deflection in a titanium alloy cantilever beam that can support a 100n load at the end of the beam

  What is the frequency of the motion what is the amplitude

a 5.70kg block hangs from a spring with spring constant 1900nm . the block is pulled down 6.80 cm from the equilibrium

  Water at 120 f and 60 psia flows through a frac12 diameter

water at 120 f and 60 psia flows through a frac12 diameter pipe at 0.6 lbms and is steadily mixed with 0.2 lbms water

  Find the natural frequencies of oscillation

find the natural frequencies of oscillation of the double-pendulum below where m1=m2=m, and L1=L2=L.

  Prepare a journal papernbsp the journal paper inhibits

prepare a journal papernbsp the journal paper inhibits -nbsp abstract-nbsp introductionnbsp literature reviewsnbsp

  The specific gravity of the solid particles is 27 for this

a sample of saturated clay from a consolidometer test has a total weight of 3.36 ib and a dry weight of 2.32 ib the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd