Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
The voltage response for the circuit is known to be v(t)= D1te^-500t + D2e^-500t. The initial current in the inductor is -10mA and the initial voltage on the capacitor = 8V. The inductor has an inductance of 4H,
a) Find the values of R, C, D1, and D2
b) Find the Ic(t) for t=0+
The Signal power to noise power ratio is an important measure of the transmission quality of any channel. If at the receiver there is a 12 dB signal to noise ratio and the received signal power is 50 micro W then calculate the received noise power..
A president, secretary, and treasurer are to be chosen from a group of 10 senior members of the IEEE student chapter at the Citadel. Assume that each member cannot serve more than one position.
In electric motor delivers 23 hp of mechanical power into a load it runs on single phase 440 VAC and is 83 percent efficient its running power is .77 and the starting current is 70 percent higher than its running current
Design a second-order band-pass IIR filter with center frequency of 450 Hz when the sampling frequency is 2000 Hz. In order to ensure the filter stability set the poles at 0.96 radial distant from the origin
For the discrete signals defined as the following: x[0]=4, x[1]=1, x[3]=-1, x[n]=0 for all other integers n. v[0]=1, v[1]=-2, v[2]=3, v[3]=-4, v[n]=0 for all other integers n. Compute the convolution x[n]*v[n] for n
An array is defined as: ARRAY DB 2 DUP(5,2,2 DUP(4,7),6) The location of ARRAY is at 500H and DS = 0 Select an instruction to read the third copy of 4. Select one: a. MOV AL,ARRAY[SI] :where SI=10 b. MOV BL,[500] c. None of the answers. d. MOV [BX+SI..
A signal is sampled every 1ms for 20ms, with the following actual values of the analogue voltage at successive sampling times. Plot the values of the voltage recorder by a 5 volt, 4 bit ADC assuming that the noise level is much lower
A balacnced, three-phase, delta-connected load is supplied by a balanced, three-phase, wye-connected source over a balanced three-phase line. the source voltages are in abc phase sequence in which Van is 19.94
The outer surface temperatures of the brick and insulation are 1260 degreeR and 560 degreeR, respectively , and there is perfect contact at the interface between the two layers. Determine at steady state the instantaneous rate of heat transfer
Use Smith Chart: A 100 Ohm air-coaxial transmission line is measured to have an input impedance of 100 + j100 Ohms. If the system is operated at 100 MHz and is one meter long, what is the terminating load impedance
An InP TED is 0.5 pm long with a cross sectional area of 10" cm2 and is operated in the transit-time mode.(a) Find the minimum electron density no required for transit-time mode.
Work out the following problem: If the analog signal to be quantized is a sinusoidal waveform, that is, x(t) = 6 sin (6283t), and if the bipolar quantizer uses 8 bits, determine 1. Number of quantization levels; 2. Step size of the quantizer ; 3. ..
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd