Find the value of the reduced volume both fluids would have

Assignment Help Mechanical Engineering
Reference no: EM13624251

Assume that oxygen(Tc =154.6K, Pc =5.046 x 106 Pa and Vc =7.32x10-5 m3/mol) and water (Tc =647.3K,Pc = 2.205 x 107 Pa and Vc = 5.6 x 10-5 m3/ mol) can be considered van der Waals fluids.

(a) Find the value of the reduced volume both fluids would have at Tr = 3/2 and Pr = 3.

(b) Find the temperature, pressure and volume of each gas at Tr = 3/2 and Pr = 3.

(c) If O2 and H2O are both at a temperature of 200 C and pressure 2.5 x 106 Pa, what are their specific volumes?

 

Reference no: EM13624251

Questions Cloud

Shorney construction company bids on projects assuming the : shorney construction company bids on projects assuming the mean idle time per worker is 72 or fewer minutes per day. a
A wire carries a current of 059 a this wire makes an angle : a wire carries a current of 0.59 a. this wire makes an angle of 68deg with respect to a magnetic field of magnitude 4.0
At 45 degrees celsius latitude the gravitational : at 45 degrees celsius latitude the gravitational acceleration as a function of elevation z above seas level is given by
Two charges a and b are fixed in place at different : two charges a and b are fixed in place at different distances from a certain spot. at this spot the potentials due to
Find the value of the reduced volume both fluids would have : assume that oxygentc 154.6k pc 5.046 x 106 pa and vc 7.32x10-5 m3mol and water tc 647.3kpc 2.205 x 107 pa and vc 5.6
Suppose that the electric potential outside a living cell : suppose that the electric potential outside a living cell is higher than that inside the cell by 0.087 v. how much work
Two tiny spheres have the same mass and carry charges of : two tiny spheres have the same mass and carry charges of the same magnitude. the mass of each sphere is 3.03 times 10-6
Suppose that 10 of all steel shafts produced by a process : suppose that 10 of all steel shafts produced by a process are nonconforming but can be reworked rather than having to
A 600 mw coal-fired power plant has an overall thermal : a 600 mw coal-fired power plant has an overall thermal efficiency of 38. it is burning coal that has a heating value of

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the number of vehicles needed to satisfy

determine the number of vehicles needed to satisfy the indicated deliveries per hour? Assume that availability = 0.90.

  When a brass specimen initially 505 in in diameter is

when a brass specimen initially .505 in in diameter is tested the maximum load of 12000lbs was recorded at an

  Determine the angular velocity theta dot of the combined

a wad of clay mass m1 with an initial horizontal velocity v1 hits and adheres to the massless rigid bar which supports

  The mass flow rate of the refrigerant is 005 kgs show the

a refrigerator uses refrigerant-134a as the working fluid and operates on an ideal vapor-compression refrigeration

  The compressor is cooled by the ambient air at 15 degc at

air enters a compressor at ambient conditions of 100kpa and 17 degc with a low velocity and exits at 1mpa 327 degc and

  Compute the stress in the bar and the resulting design

a steady tensile load of 5.00kn is applied to a square bar 12mm on a side and having a length of 1.65m. compute the

  Moist air at standard conditions in an indoor building

moist air at standard conditions in an indoor building space has a dry bulb temperature of 72f and relative humidity

  Neglect the small mass and friction of the pulley and

the system is released from rest with the cable taut. neglect the small mass and friction of the pulley and calculate

  Explain midrange and amplitude components

Midrange and amplitude components, A shaft is subjected to a completely reversed bending stress such that Xmax=40kpsi and Xmin=-40kpsi

  Solve for u as a function of y as done in the class for

consider incompressible viscous flow between two very long plates separated by a distance h. the bottom plate is

  Determine the reactions at these supports

The 25-kg bar has a centre of mass at G.If it is supported by a smooth peg at C,a roller at A and cord AB, determine the reactions at these supports.

  Find the transfer function for the following impulse

find the transfer function for the following impulse responsefind the transfer function for the following impulse

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd