Find the total horizontal force on the surface

Assignment Help Mechanical Engineering
Reference no: EM13701690

Gate AB in fig 2 is a one-quarter circle, 5 m wide into the paper, hinged at B and resting on a smooth wall at A.

a) Find the total horizontal force on the surface.

b) Find the total vertical force on the surface.

c) Find the point of application (Center of Force) of the resultant force from point A (XA, XB)).

d) Compute the reaction forces at A and B

I included diagram and questions too.

Reference no: EM13701690

Questions Cloud

Vertical cylinder fitted with a frictionless piston contains : A vertical cylinder fitted with a frictionless piston contains argon at 100C. The piston has a mass of 5kg and a diameter of 100mm, and the ambient pressure outside the cylinder is 97kPa. If the cylinder volume is 2 liters, what is the mass of argon ..
A piston-cylinder device contains steam initially : A piston-cylinder device contains steam initially at 1 Mpa, 450 degrees celcius and 2.5 m^3. Steam is allowed to cool at constant pressure until it first starts condensing. Show the process on T-v diagram with respect to saturation lines and determin..
Dislocation loop in form of circle-specify burgers vector : Sketch a dislocation loop in the form of a circle and specify the Burgers vector. Show portions of the dislocation that are screw-like and those that are edge-like in nature. Considering the energy per unit length of the screw dislocation being somew..
Analyze and explain the facts of both cases : Research, analyze and explain the facts of both cases.  Do not confuse your personal opinion or assumptions in this part of the paper.  Explain the facts of each case.
Find the total horizontal force on the surface : Gate AB in fig 2 is a one-quarter circle, 5 m wide into the paper, hinged at B and resting on a smooth wall at A. Find the total horizontal force on the surface.. Find the total vertical force on the surface.
Determine rate of insulin production from gel in moles : Genetically engineered bacteria (used to produce insulin) are immobilized in a solid agar disc (cylinder with flat surface facing up - 100 cm diameter, 5 cm height), which is exposed to large volume of stirred liquid media on both of the flat surface..
Individual gas and liquid mass transfer coefficients : A mass transfer tower operating at 1 atm and 300 K uses water, which enters free of ammonia at the top, to reduce the ammonia (NH3) concentration in air exhausted from a reactor. At one plane (W) in the tower, the concentrations of ammonia in the liq..
What temperature does the piston fall below the stops : A vertical cylinder fitted with a piston contains air initially at 120kPa and 100C. The piston is restrained by a set of stops. The piston diameter is 0.1m, its mass is 5kg, and the ambient pressure and temperature are 100kPa and 20C. The cylinder is..
Determine the entrance length : Water flows through a 1 [cm] diameter circular pipe at a flow rate of 127 [cm3/s]. Determine the entrance length.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd