Find the time at which the capacitor is fully charged

Assignment Help Electrical Engineering
Reference no: EM13250587

A 50V DC source is connected in series with a switch, an 8.2k ohm resistor, and a 0.01 microfarad capacitor. There is no initial charge on the capacitor and the switch is open. Determine both A & B:

A) The capacitor voltage 50 microseconds after the switch is closed

B) The time at which the capacitor is fully charged

Reference no: EM13250587

Questions Cloud

Design a digital controller that has a bandwidth of 100 hz : The read arm of a computer disk drive has the transfer function of G(s) = 1000/s^2. Design a digital controller that has a bandwidth of 100 Hz and a phase margin of 50 degrees. Use a sample rate of 6kHz.
Determine the self-inductance of the coil : The current in a coil drops from 3.1 A to 2.6 A in 0.53 s. If the average emf induced in the coil is 12 mV, what is the self-inductance of the coil
Construct a control chart for the process : Construct a control chart for the process, assuming a fraction defective of 2%, using two-sigma control limits. Is the process in control?
Explain hydrogen gas at standard temperature and pressure : What volume, in L, of hydrogen gas at standard temperature and pressure (STP) is produced from reacting 0.333 L of 0.807 M hydrochloric acid with aluminum metal? (1 mol of gas @ STP = 22.4 L).
Find the time at which the capacitor is fully charged : A 50V DC source is connected in series with a switch, an 8.2k ohm resistor, and a 0.01 microfarad capacitor. There is no initial charge on the capacitor and the switch is open. Determine both A & B The time at which the capacitor is fully charged
Find the self-induced emf in the solenoid : A technician wraps wire around a tube of length 37 cm having a diameter of 8.3 cm. If the current in this solenoid increases at the rate of 2 A/s, what is the self-induced emf in the solenoid
What are the four types of resource constraints : What are the four types of resource constraints? Please list them and provide an example of each.
When a chemical messenger functions : When a chemical messenger functions in an endocrine fashion, it must have:
What is the mass of the ammonia : A metal sphere is filled with ammonia as part of a refrigeration device. what is the mass of the ammonia if it fills up half of the sphere

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Find the normalized voltage magnitude values at the load

A table of values of the normalized magnitude of the voltage phasor on the line as a function of position on the line, with the normalization done relative to the value of the voltage magnitude at the voltage maximum point on the line.

  Determine the energy in the signals odd part

A signal x(t) can be represented as x(t)=xe(t)+xo(t) where xe(t)=(1/2){x(t)+x(-t)} is the even part, and xo(t)=(1/2){x(t)-x(-t)} is the odd part of the signal. Let x(t) be an energy signal with an energy of 20 Joules. Suppose the even part of x(t) is..

  Describe what transpires when an interrupt occurs

What is an interrupt service routine What benefit does the ISR have over standard polling code Discuss challenges experienced in developing the dual interrupt software code.

  Explain what is the framework or reference model

1. There are 4 main classes of network topologies, what are they 2. In communications over a network, protocols are required. What is the framework or reference model that makes this possible

  Give explanation to electric circuits

Explanation to "Electric circuits" question, The voltage across a load is v(t) = 260 sin (377t + 10 °) and the current through the load is i = 100 sin (377t + 10°). What is the RMS power?

  Calculate the rms value of the phase currents

A balanced three-phase inductive load is supplied in steady state by a balanced three-phase voltage source with a phase voltage of 120 V rms. The load draws a total of 10 kW at a power factor of 0.85. Calculate the rms value of the phase currents

  Amplify the signal of a microphone with internal resiatance

What value of emitter resistor would you choose, if: a) You have to amplify the signal of a microphone that has an internal resistance of 100K using a Common Emitter bias configuration b) you have to drive a load of 50 with an Emitter Follower cir..

  Develop a bipolar transistor amplifier with a voltage gain

The aim of this experiment is to develop a bipolar transistor amplifier with a voltage gain of minus 25. The amplifier must accept input signals from a source impedance of 1 kW and provide an undistorted output amplitude of 5 V when driving a 560..

  What is the footprint of the entire focal plane array

the SABER instrument aboard the TIMED satellite orbits the earth in a sun-synchronous polar orbit 625 Km above the earth. each of the 10 SABER focal plan detectors is 0.14mm high by 2.0mm wide. the focal plane array is 4.882*4.882mm in size

  What is the fastest expected change time

A liquid level system converts a 4-10 m level into a 4-20mA current. Design a three mode controller (PID im assuming) that outputs 0-5 volts with 50% PB, 0.03 min integration time, and 0.05 min derivative time.

  What will be the speed if the motor current is 10a

The motor resistance is 0.5ohm and the magnetic circuit may be assumed unsaturated. What will be the speed if: (i) the load torque is increased by 44%, (ii) the motor current is 10A

  Determine the suitable size of cable for electrical wiring

How to determine the suitable size of cable for Electrical Wiring Installation and please with Solved Examples.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd