User Account

All Pages

Find the thrust force of the engine

Assignment Help Mechanical Engineering
Reference no: EM13709963

A high-speed boat is powered by a water jet pump engine, similar to a jet engine on airplanes. The engine takes in water at the bow through a tube with diameter 1 ft, and the water is pumped out the stern of the boat through a 3-in diameter tube. The flow rate is 5000 gpm. Neglecting any frictional loss, find: (a) the thrust force of the engine; (b) the maximum speed of the boat, if the drag coefficient is 0.005 with a corresponding projected area of 500 ft2; (c) If the pump is 100% efficient, how many hp are required?

Reference no: EM13709963

Questions Cloud

Determine the rate of heat transfer from the air : Air enters the evaporator at 14.7 psia and 90 F with a volumetric flow rate of 200 ft3/min. Refrigerant 134a at 20 psia with a quality of 30 % enters the evaporator at a rate of 4 lbm/min and leaves as saturated vapor at the same pressure. Assume ste..
Consider a cylindrical specimen of a steel alloy : Consider a cylindrical specimen of a steel alloy 8.0 mm (0.3150 in.) in diameter and 89 mm (3.504 in.) long that is pulled in tension. Determine its elongation when a load of 57810 n (13000 lbf) is applied. The tensile stress-strain behavior for this..
Determine the power rating of the electric heater immersed : You are assigned to design a heating system for a swimming pool that is 2 m deep, 20 m long and 20 m wide. The client desires that the heating system be large enough to raise the water temperature from 2 C to 3C in 2 hours. The rate of heat loss from..
Determine the distance from the leading edge of the plate : Air at 25°C and 1 atm is flowing over a long flat plate with a velocity of 8 m/s. Determine the distance from the leading edge of the plate where the flow becomes turbulent, and the thickness of the boundary layer at that location.
Find the thrust force of the engine : A high-speed boat is powered by a water jet pump engine, similar to a jet engine on airplanes. The engine takes in water at the bow through a tube with diameter 1 ft, and the water is pumped out the stern of the boat through a 3-in diameter tube.
Determine the displacement of the vertical edge : A rectangular material sample (2 in tall and 1 in wide) is subjected to a vertical tensile stress of 50,000 psi on its upper edge. The bottom edge of the sample is constrained from displacing in the vertical, or y, direction but is free to expand or ..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Magnitude of the particles acceleration four seconds later

A particle travels around a circular path having a radius of 80m. It is initially traveling with a speed of 10 m / s and its speed then increases at a rate of v = (0.05v) m /s2. Determine the magnitude of the particle's acceleration four seconds late..

  Determine the maximum contact pressure

The wheel of a crane lift is rolling on a flat rail. The radius of the wheel is 4 in, the contact length and force are 2.5 in and 1 ton respectively, and E = 30 MPa and ν = 0.3 for both parts. Determine (a) the maximum contact pressure, (b) the wi..

  Pictorial view autocad figure 2 gives a pictorial view of a

figure 2 gives a pictorial view of a slotted guide. draw the following views in third angle ltbrgtprojection. ltbrgta a

  Do a regression analysis to find the best fit for the data

the acceleration due to gravity at an altitude y above the surface of the earth is given byymnbspnbspnbsp

  A flow of 05 kgs superheated steam at 5 mpa 400c and a

a flow of 0.5 kgs superheated steam at 5 mpa 400c and a flow of liquid water at 5 mpa 40c are mixed. if saturated

  Consider the flow of a uniform stream of speed

Consider the flow of a uniform stream of speed V in the x-direction and a sink of strength Q at the origin. Find the stagnation point(s) and the equation of the stagnation streamline. Sketch (freehand) the flow streamlines

  Determine the work and heat transfer for the process

Two kilograms of Refrigerant134a, initially at 2 bar and occupying a volume of 0.12 m3, undergoes a process at constant pressure until the volume has doubled. Kinetic and potential energy effects are negligible. Determine the work and heat transfe..

  Temperature sensors sensitivity

A temperature sensor's sensitivity is given as 5mv/0.1oF. The sensor can measure from -100oF (that is negative 100F) to 150oF. Find out the sensor possible output values for a measured value of 30F for the following accuracies: ±0.5% of FS error/ ±..

  A 150-lbm astronaut took his bathroom scale aspring scale

a 150-lbm astronaut took his bathroom scale aspring scale and a beam scale compares masses to themoon where the local

  Show the cycle on a t-s diagram with respect to the

consider a 210mw steam power plant that operates on a simple rankine cycle. steam enters the turbine at 10mpa and 500oc

  Water vapor initially at 30 mpa and 300degc is contained

water vapor initially at 3.0 mpa and 300degc is contained within a piston-cylinder. the water is cooled at constant

  Individual gas and liquid mass transfer coefficients

A mass transfer tower operating at 1 atm and 300 K uses water, which enters free of ammonia at the top, to reduce the ammonia (NH3) concentration in air exhausted from a reactor. At one plane (W) in the tower, the concentrations of ammonia in the liq..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd