User Account

All Pages

Find the temperature to which the air is cooled and the

Assignment Help Mechanical Engineering
Reference no: EM13643451

An air-conditioned room requires 30 m3 /min of air at 1.013 bar, 20 degree C, 52.5% RH. The steady flow conditioner takes in air at 1.013 bar, 77% RH, which it cools to adjust the moisture content and reheats to room temperature. Find the temperature to which the air is cooled and the thermal loading on both the cooler and heater. Assume that a fan before the cooler absorbs 0.5 kW, and that the condensate is discharged at the temperature to which the air is cooled.

Reference no: EM13643451

Questions Cloud

A small car collides with a large truck is the magnitude of : a small car collides with a large truck. is the magnitude of the force experienced by the car greater than less than or
Two nanowires are separated by 12 nm as measured by stm : two nanowires are separated by 1.2 nm as measured by stm. inside the wires the potential energy is zero but between the
Find the final mass of nitrogen in the tank and the final : a steel cylinder initially contains nitrogen gas at 200 kpa and 25 degree at celsius. the cylinder is in is connected
A radar trap operates at a frequency of f10ghz the speed : a radar trap operates at a frequency of f10ghz. the speed of microwaves is v3.0108 ms. the microwave beam is aimed at a
Find the temperature to which the air is cooled and the : an air-conditioned room requires 30 m3 min of air at 1.013 bar 20 degree c 52.5 rh. the steady flow conditioner takes
Suppose the clay ball is dropped from the ceiling onto an : a massless pan hangs from a spring that is suspended from the ceiling. when empty the pan is 52 cm below the ceiling.
Determine the mass flow rate of spray water and the power : an industrial process requires an atmosphere having a rh of 88.4 at 22 degree c and involves a flow rate of 2000 m3h.
Cooling water enters a cooling tower at a rate of 1000 kgh : cooling water enters a cooling tower at a rate of 1000 kgh and 70 degree c. water is pumped from the base of the lower
Estimate the moisture picked up by 1 kg of dry air and the : a grain dryer consists of a vertical cylindrical hopper through which hot air is blown. the air enters the base at 1.38

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The room temperature yield strength of ni is 100mpa 15000

the room temperature yield strength of ni is 100mpa 15000 psi and furthermore sy diminishes about 5mpa for every 50

  Calculate the hourly gas flow rate for the conditions given

calculate the hourly gas flow rate for the conditions given as followsreadings differential pressure 50-in water static

  A shaft is subjected to a maximum load of 10 kn it is

a shaft is subjected to a maximum load of 10 kn. it is designed to withstand a load of 15 kn. if the maximum load

  Estimate the wavelength corresponding to maximum emission

estimate the wavelength corresponding to maximum emission from each of the following surfaces the sun a tungsten

  A single-effect evaporator system with thermal

a single-effect evaporator system with thermal recompression is being used to concentrate skim milk from an initial

  Determine the rate of heat transfer between the pipe and

consider a horizontal pipe with a constant diameter. water constant density p 1000 kgm3 enters the pipe at

  Determine for the modified cycle a the coefficient of

air enters the compressor of an ideal brayton refrigeration cycle at 120 kpa and 275 k. the compressor pressure ratio

  The rest exits at another location with a pressure of 006

steam at 160 bar 520 degrees celsius and with a mass flow rate of 250 kgs enters a turbine operating at steady state

  What fraction n of the weight of the jet airplane is the

what fraction n of the weight of the jet airplane is the net thrustnozzle thrust t minus air resistance r required for

  Determine a suitable length for the bolt rounded up to the

a 1.5 inch thick steel plate and a 0.5 inch thick cast iron plate are compressed with 14- 20 unc grade 5 bolt and

  A nozzle with inlet area of 800 cm2 and inlet steam

a nozzle with inlet area of 800 cm2 and inlet steam velocity is 10ms. the steam pressure is 800kpa and temperature is

  Assuming ideal gas behavior for the air and neglecting

a rigid well-insulated tank with a volume of 3 fe contains air at p1 22 lbfin2 and t1 475 bullr. the air is stirred by

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd