Find the temperature of source and sink

Assignment Help Mechanical Engineering
Reference no: EM13212478

a heat engine working on carnot cycle converts 25% of heat into work when the temperature of the sink is reduced by 353 k the efficiency gets doubled .find the temperature of source and sink.

Reference no: EM13212478

Questions Cloud

What is going on in the economy after the minimum wage : The eq'm wage is currently $7/hour, eq'm Q of labor is 35 hours. Using generic QLS and QLD labels (if necessary), show what is going on in this economy after the minimum wage goes into effect. How much unemployment results
Development of risk control strategies : Explain the process of risk identification, risk assessment, and the development of risk control strategies in designing security for an information management system.
What tightening torque should be used : What tightening torque should be used if the connection is permanent and the fasteners are lubricated? What portion of the external load is taken by the bolts? By the members?
Calculate the mass of neon gas in si units : A volume of 1.8 L of neon gas (monatomic) is at a pressure of 3.4 atmospheres and a temperature of 370 K. The atomic mass of neon is 20.2 g / mol. Calculate the mass of neon gas in SI units.
Find the temperature of source and sink : a heat engine working on carnot cycle converts 25% of heat into work when the temperature of the sink is reduced by 353 k the efficiency gets doubled .find the temperature of source and sink.
Discuss how the strategies are applied : Describe three that you think are the most important, and discuss how the strategies are applied and describe three that you think are the most important and discuss how the strategies are applied.
Calculate the time rate of change : Calculate the time rate of change dHB/dt of angular momentum about point B when the particle passes the bottom of the guide at C.
What is the probability that attendance is greater : The attendance at baseball games at a certain stadium is normally distributed, with a mean of 44,000 and a standard deviation of 2500. For any given game: a) What is the probability that attendance is greater than 46,000 b) What is the probability ..
Compute the irr for project : Compute the IRR for this project. How many IRRs are there? Using the IRR decision rule, should the company accept the project? What's going on here?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd