Find the rate of waste heat rejection kjhr and the number

Assignment Help Mechanical Engineering
Reference no: EM13623933

A schematic must show TH, TC, QH, QC, WCYCLE. Always show the hot reservoir at the top & cold reservoir at the bottom. Use arrows to show directions and indicate numeric values that are given.

(A) An electrical window air conditioner with a cooling capacity of of 8000 kJ/hr draws 6.00 amps of electrical current at 120 volts. The electricity price is $0.15/kwhr. Find the cycle coefficient of performance, the rate of waste heat rejection (kJ/hr) and the electrical cost to operate the unit steadily for 1 day ($/day). Include a complete schematic diagram in your write-up clearly showing hot (top) & cold (bottom) regions and arrows showing all energy exchanges.

(B) The 90 kW of electrical power needed for an emergency field hospital in Haiti is to be generated by a diesel fueled engine-generator set. The thermal efficiency is 27%. The fuel tank holds 10 barrels of diesel fuel (42 gallon/barrel). Combustion of one gallon of diesel fuel releases 130,000 kJ of energy. Find the rate of waste heat rejection (kJ/hr) and the number of hours the unit can operate steadily on one full tank of fuel.

Include a complete schematic diagram in your write-up clearly showing hot (top) & cold (bottom) regions and arrows showing all energy exchanges.

Reference no: EM13623933

Questions Cloud

An automatic external defibrillator delivers 125j of energy : an automatic external defibrillator delivers 125j of energy at a voltage of 1050v. what is the capacitance of this
Assume that the expansion is adiabatic with negligible : air expands through a nozzle from a chamber pressure and temperature of 300 psia and 1000 r respectively to an exit
At time t 0 the point at x 0 has a displacement of 0 and : the displacement of a string carrying a traveling sinusoidal wave is given byyxt ym coskx - 2pft - fat time t 0 the
A truncated cone 30 cm high is constructed with aluminum : a truncated cone 30 cm high is constructed with aluminum. the diameter at the top is 7.5 cm and the diameter at the
Find the rate of waste heat rejection kjhr and the number : a schematic must show th tc qh qc wcycle. always show the hot reservoir at the top amp cold reservoir at the bottom.
How much kinetic energy kair did the air molecules gain : a coffee filter of mass 1.7 grams dropped from a height of 1.3 m reaches the ground with a speed of 2.6 ms. how much
What is the angular frequency of the charge oscillations in : a 14.0 mu f capacitor and a 5.25 mhinductor are connected in series with an open switch. the capacitor is initially
Suppose that x y and z are independent random variables : suppose that x y and z are independent random variables each having a standard normal distribution. determine
What are the reaction forces and reaction moments what is : consider a solid bar in the shape of a hook shown in figure 1. a coordinate system is also shown. a load p is applied

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd