Find the probibility thats screws drawn will be defective

Assignment Help Electrical Engineering
Reference no: EM13247258

Three screws are drawn at random from a lot of 200 screws, 10 of which are deffective. Find the probibility thats the screws drawn will be nen defective in drawing
a.) WITH replacement
b.) WITHOUT replacement

Reference no: EM13247258

Questions Cloud

A demand curve that is horizontal indicates that the commodi : A demand curve that is horizontal indicates that the commodity
What are the equivalent admittance and conductance : Three branches having impedances of 3 + /4 O, 16 - /12 ft, and - / 4 ft, respectively, are connected in parallel. What are the equivalent (a) admittance, (b) conductance, and (c) susceptance of the parallel connection in millisiemens
Calculate the resistivity of your skin : The width of the contact of each wire with your skin is 1.10 cm and the thickness of the conducting layer of your skin is 0.023 mm, calculate the resistivity of your skin
Calculate the power factor at whic the source operates : In each of the three phases in a balanced delta- connected load is composed of a 10mF capacitor in parellel with a series-connected 470 ohm resistor and 4mH inductor combination, assume a phase voltage of 400 V at 50 Hz
Find the probibility thats screws drawn will be defective : Three screws are drawn at random from a lot of 200 screws, 10 of which are deffective. Find the probibility thats the screws drawn will be nen defective in drawing a.) WITH replacement
Calculate the new demand for dollars at each exchange rate : Suppose the demand for dollars increases by 300 billion at each exchange rate. Explain if the increase in demand results from a large purchase b the Chinese of a new American-made airplane or a large purchase by Americans of new lower priced Chinese-..
Explain what action should be taken in terms of adjusting : Explain what action should be taken in terms of adjusting output if it is determined that marginal cost is greater than marginal revenue.
Write the boolean equation for emergency : A jet has 4 engines. Each engine gives a FAIL signal which is TRUE if the engine is broken, and is FALSE if the engine is working fine. The plane can fly as long as at most 1 engine is broken.
Determine the force constant of this spring : To stretch a certain spring by 3.00cm from itsequilibrium position requires 9.50J of work, What is the force constant of this spring

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Digital communications -order the following modulation types

Digital Communications, Order the following modulation types in terms of spectral efficiency (best to worse) and explain

  Find the magnitude of the phase current in the load

A three-phase generator is Y-connected. It has phase voltages of 277 V. A delta-connected load is attached to the lines coming from the generator. Each phase of the load has an impedance of 9/41

  What is the value of the feedback resistor required

A temperature sensor covers a range of 0 to 70 degrees C with an output sensitivity of 2 mV/degree C. The sensor is input to an ADC with voltage range of 0 to 4V. What is the value of the feedback resistor required for an inverting amplifier circu..

  What does the documentation mean

Using the Internet, a magazine, or a provided list of memory modules, determine the exact part numbers and quantities of memory modules that you would buy. List them with the location of where you obtained the information.

  Find how much energy the resistor disspates for t

B.) Write an equation for v(t) for t > 0 C.) Write an equation for the power absorbed by resistor for t >= 0 D.) Find how much energy the resistor disspates for t >= 0 E.) How much energy is stored in capacitor at t=0

  Which has the higher resistance in copper wire

which has higher resistance: the copper wire that carries the power from Bonneville Dam to your circuit breaker box, the copper wire that carries the power from there to your computer, or the copper wire that runs from the from one side of the chi..

  Derive an expression for the built-in voltage

Consider a p-type semiconductor substrate with Na =10^15 cm^-3. A region of heavily p+ doped material is formed by ion implantation as shown in the sketch below.Derive an expression for the built-in voltage under equilibrium conditions.

  Determine the value of the transfer function of the filter

The input to a certain filter is given by Vin(t)=2cos(10000pi*t-15deg) and the steady state output is given by Vout(t)=5cos(10000pi*t+25deg). Determine the (complex) value of the transfer function of the filter for f=5000 Hz.

  Determine the phase currents iab-ibc and ica of the load

A balacnced, three-phase, delta-connected load is supplied by a balanced, three-phase, wye-connected source over a balanced three-phase line. the source voltages are in abc phase sequence in which Van is 19.94

  Define filter has steadily increasing attenuation

A filter has the following characteristics: Attenuation is 0 dB from 0 Hz to 2.5 kHz. Phase angle decreases linearly with increasing frequency above 2.5 kHz. Above 5 kHz the filter has steadily increasing attenuation.

  Find the overall gain gv and the equivalent circuit

Two amplifiers(CS) connected in cascade. The input voltage to the first stage has a source voltage Vsig and Rsig= 100KOhm. Rv=10KOhm AND IS CONNECTED TO THE DRAIN OF THE SECOND STAGE. BOTH TRANSISTORS HAVE Id=.25mA and Vov=.25V

  Which type of wires to use minimize resistance of the wire

In US, electric wires are classified based on their gauge numbers. The larger the gauge number is, the smaller the diameter of the cross-section of the wire becomes. You are given four different types of wire with gauge numbers 1, 3, 7, and 8.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd