Find the probability of error in digital communication

Assignment Help Electrical Engineering
Reference no: EM13227092

A digital communication system transmits one of the three values -1,0,1. A channel adds noise to cause the decoder to sometimes make an error. The error rates are 12.5% if a -1 is transmitted, 75% if a 0 is transmitted, and 12.5% if a 1 is transmitted. If the probabilities for the various symbols being transmitted are P [ - l ] = P[l] = 1/4 and P[0] = 1/2, find the probability of error. Repeat the problem if P[-1] = P[0] = P[l]

Reference no: EM13227092

Questions Cloud

What are the risks and disadvantages of such alliances : What are the risks and disadvantages of such alliances? What strategic alliances does your case study company employ?
Identify and explain the meaning and strategic significance : What is the strategy of your case study company? Identify and explain the meaning and strategic significance of each of the following terms
What are some of the uses of adc undersampling : Suppose we had connected at the input to channel 0 a circuit of the type that attenuates all frequencies above 50 Hz at a rate of 6 dB/octave. What will we then see in the output when we apply 4960 Hz at the input
What does case study company do to ensure ethical compliance : Does a company have a duty to go beyond legal requirements and conform to the ethical norms of the societies in which it operates? What is the case for why business strategies should be ethical? What does your case study company do to ensure ethic..
Find the probability of error in digital communication : A digital communication system transmits one of the three values -1,0,1. A channel adds noise to cause the decoder to sometimes make an error. The error rates are 12.5% if a -1 is transmitted, 75% if a 0 is transmitted, and 12.5% if a 1 is transmi..
Explain what is involved in building capabilities internally : Explain what is involved in building capabilities internally? What steps are required? How much time does it take? How hard is it? Support your answer. How does your case study company do this?
Discuss the type of control mechanisms that managers can use : Discuss the type of control mechanisms that managers can use to monitor the performance of empowered employees. Apply this question to your case study company.
Find out pmn after the addition of the na2h2y : 25.00 mL of 0.0200 M MnCl2 is titrated with 0.0250 M Na2H2Y. Both solutions are buffered to pH 8.20. Determine pMn after the addition of the following volumes (mL) of the Na2H2Y.
What is the probability of obtaining one red ball : An urn contains 4 red balls and 2 black balls. Two balls are chosen at random and without replacement. What is the probability of obtaining one red ball and one black ball in any order Verify your results by enumerating all possibilities using a c..

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Explain the boolean expression in sum of product form

b. Draw the logic diagram, using the original Boolean expression. d. Obtain the truth table of the function form the simplified expression and show that it is the same as the part one. e. Draw the logic diagram from simplified expression, and compare..

  Verify gauss law by considering the total flux out of cube

Simple in concept, but complicated in execution because of the resulting integrand: Explicitly evaluate (in Cartesian coordinates) the surface integral (flux) over the surface S defined as the face of the cube that is perpendicular

  Which one will store most charge

For a circuit with resistor of 10 K ohm and a capacitor of 5 micro Farads, what is the time constant in second?

  Contrast cdma techniques with frequency hopping

CDMA is a multiple access technique to allow multiple users to share the same bandwidth, based on the orthogonality of their spreading codes. CDMA is a descendent of the direct sequence spread spectrum (DSSS) technology designed for antijam (AJ).

  A circuit contains two devices that are connected

A circuit contains two devices that are connected in parallel. If the resistances of one of these devices is 12ohms and the resistance

  Combinational logic devices for specific purposes

Interpret manufacturer's data sheet to select appropriate combinational logic devices for specific purposes

  What is the ber at the output of the receiver in clear air

What is the BER at the output of the receiver in clear air conditions, and the average time between errors? Give your answer in years, days, or hours as appropriate. Assume an implementation margin of 0.5 dB.

  What is the per unit value if we change the base

A generator is rated at 500 MVA (three phase) and 22 kV (line-to-line). Its Y-connected windings have a reactance of 1.1 per unit. Find the ohmic value of the reactance of the windings. What is the per unit value if we change the base to 200 MVA a..

  Calculate the power in each resistor

If R2 = 2R1, R3 = 3R1 and the total power taken by the circuit is 480 watts. Calculate the power in each resistor

  Explain what should the signal definitions be

What should the signal definitions be for the equations, such that the minimal about of hardware (gates) are used assuming we have an abundance of NAND gates Show the signals definitions and resulting circuitry.

  What approximate minimum ber is required for voice signals

What approximate minimum BER is required for voice signals, data signals and what is the approximate BER level for the optical fiber systems ?

  Find two designs using open-circuited stubs

A load impedance ZL = 100 + j80 is to be matched to a 75 ohm line using a single shunt-stub tuner. Find two designs using open-circuited stubs. Include both smith chart and analytical analysis.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd