Find the power in hp of the compressor the heat rate added

Assignment Help Mechanical Engineering
Reference no: EM13630452

A wet compression refrigeration cycle uses HFC-134a as the working fluid and operates between 75 F and 8 F. Use a mass flow rate of 50 lbm per hour. Use the tables (in the text) find the enthalpy values and the diagram the cycle on the chart (provided). Find the power (in HP) of the compressor, the heat rate added (in BTU/hr), and the heat rate rejected (in BTU/hr), and compare the Coefficient of Performance and the Coefficient of Refrigeration for these cycles with the Carnot Cycle Coefficient of Performance and Coefficient of Refrigeration.

Reference no: EM13630452

Questions Cloud

Find the velocity of the satellite relative to that of the : suppose a satellite in geosynchronous orbit has just passed above the international space station with respect to the
Conduct a hypothesis test to determine if the percentage of : according to a recent gallup poll more americans who own credit cards say they always pay the full amount of their
Use the perfomance characteristics of the marine propeller : total power required to overcome viscous resistance and wave drag is 11.4 mw. use the perfomance characteristics of the
Assume the distributions of time a customer is on hold are : a customer service representative was interested in comparing the average time in minutes customers are placed on hold
Find the power in hp of the compressor the heat rate added : a wet compression refrigeration cycle uses hfc-134a as the working fluid and operates between 75 f and 8 f. use a mass
Find the 95 confidence interval for the variance of the : find the 95 confidence interval for the variance of the heights of maple trees if a sample of 21 trees has a standard
Determine the minimum coefficient of static friction : if the coefficient of static friction between the crate and ground is 0.3 determine the minimum coefficient of static
Find the 95 confidence interval for the variance of the : find the 95 confidence interval for the variance of the heights of maple trees if a sample of 21 trees has a standard
Dtermine the mass rate of water flowing kgs height : a 5 cm orifice meter is being used to measure the flowrate of 70 degree c water. the mercury manometer shows a height

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the minimum number of expansion joints required

a bridge to be fabricated of steel girders is designed to be 500 m long and 12 m wide at ambient temperature assumed 20

  Determine the magnitude and direction fo the force p

A 200 kg crate is to be supported by the rope and pulley arrangement shown. Determine the magnitude and direction fo the force P that must be exerted on the freee end of the rope to maintain equillibrium.

  The premissible stresses in the key are 55 nmm2 in shear

a belt pulley is fastened to a 75 mm shaft running at 360 rpm by means of a key 18 mm wide and 125 mm long. the

  A househusband is steaming beef for his family in a pan

1. a househusband is steaming beef for his family in a pan with a surface area of 23.544 cm2 that is covered with i a

  How accurate is the ideal gas model for predicting the mass

1. an employee at general electric must order bottles of compressed methane to run her gas oven test facility. the

  A plastic ring or hula-hoop is thrown to the right with a

a plastic ring or hula-hoop is thrown to the right with a velocity of 8ms and it moves in such a way that it produces a

  Determine the electrical power input to the pump

determine the electrical power input to the pump. the density of water is 1kg/l.

  It has been determined that a point in a load-carrying

it has been determined that a point in a load-carrying member is subjected to the following stress condition sx 400 mpa

  The operating reflux ratio is 30 assume that raoults law

distillation of multicomponent alcohol mixture. a feed of 30 mol methanol a 20 ethanol b 15 n-propanol c and 35

  Determine the following i the compressor efficiency

an engine operates on an air-standard brayton cycle with reheat. the work required to compress the air in one stage

  A gas turbine brayton cycle operates with an intercooler a

a gas turbine brayton cycle operates with an intercooler a re-heater and a regenerator. air enters the engine at 14 psi

  A four-cylinder engine with a 95-cm bore and an 875-cm

a four-cylinder engine with a 9.5-cm bore and an 8.75-cm stroke has a 7 clearance. the engine rotates at 2500 rpm. the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd