Find the potential drop from x2 to x1 in terms of p1 and p2

Assignment Help Electrical Engineering
Reference no: EM13266235

Consider a 1-D semiconductor system when we have a perfect balence of drift and diffusion of holes. that is the total Jp=Jp, diffusion +Jp, drift = 0. P(x=x1)=p1, P(x=x2)=p2. find the potential drop from x2 to x1 in terms of p1 and p2

Reference no: EM13266235

Questions Cloud

What is martin weighted average cost of capital : Martin Corporation is financed with 40% debt and 60% common equity. The after tax cost of debt is 10% and the cost of common equity is 14%. What is Martin's weighted average cost of capital?
What is the npv of accepting the system : What will be the annual net savings? Assume that the T-bill rate is 2.4 percent annually.
Convert the weigh to mass slugs using g : There is a damping coefficient of 18 lbs(ft./s). A weight of 96.6 pounds is attached to the spring, moved to 5 ft. above the equilibrium point and released with an initial velocity of 45 ft./s. Do not forget to convert the weigh to mass (slugs) us..
What amount must you donate to endow the scholarship : You want to endow a scholarship that will pay $5,000 per year forever, starting one year from now. If the school's endowment discount rate is 9%, what amount must you donate to endow the scholarship?
Find the potential drop from x2 to x1 in terms of p1 and p2 : Consider a 1-D semiconductor system when we have a perfect balence of drift and diffusion of holes. that is the total Jp=Jp, diffusion +Jp, drift = 0. P(x=x1)=p1, P(x=x2)=p2. find the potential drop from x2 to x1 in terms of p1 and p2
What is the value of its forgone revenue : Assuming the spot rate equals $1.298 three months from today, would entering into the forward contract have been a good idea in this case? Explain your answer.
Explain the conversion of methyl isonitrile to acetonitrile : For the conversion of methyl isonitrile to acetonitrile in the gas phase at 250 oC CH3NC CH3CN the following data have been obtained
Impact of technology and innovation on social change : Please use real-life and detailed examples to DISCUSS topic(s) related to the impact of technology and innovation on social change as it has progressed over the years and into today.
Explain the negative charge of the benzyl and anion : Use resonance forms to show the delocalization (over four carbon atoms) of the negative charge of the benzyl and anion

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Determine binary code produced by adc quantization error

Assuming that a 12-bit ADC channel accept analog input ranges from 0 to 20 volts, determine the following a) number of quantization levels b) step size of the quantizer or resolution

  Design a 3 bit combinational circuit 2s complimenter

a. Design a 3 bit combinational circuit 2's complimenter. (the circuit generates the 2's compliment of the input 3-bit binary number). [Show all work leading to the circuit implementation]

  Calculate terminal voltage and developed torgue of motor

A six pole,60 Hz synchronous motor is connected to an infinit bus of 15 KV through a transmission line.The synchronous reactance of the motor is 5 ohm ,and the inductive reactive reactance of the transmission line is 2 ohm

  Find an xc value to put in parallel with the motor

A P=900W electric motor with pf=0.82 lagging is connected to a 240 Vrms 60 hertz source. a) Draw an equivalent circuit showing impedance and phasor values for Vs, R and X. b) Find an Xc value to put in parallel with the motor which corrects the pf to..

  What is the equilibrium hole concentration

A Si sample is doped with 10^17 As atoms/cm^3. What is the equilibrium hole concentration P0 at T=300K?

  What should thickness h be so that touch sensor registers

A touch sensor base on a piezoresistor built into a micromechanical cantilever made of silicon is cnnected in a Wheatstone-bridge configureation with a Vo = 1 volt. If L = 1.44cm and W = 1 cm

  Calculate the eigen-value for the system

Show (prove) that the signal 3^j2t is an eigenfunction of any LTI system, and nd the formula for the eigenvalue. That is, use the convolution integral and simplify to show that if you input 3^j2t into an LTI system

  Calculate the magnetizing current and core losses

A transformer on no load takes 4.5 A at a power factor of 0.25 lagging when connected to a 120V, 60Hz supply, the number of turns of the primary winding is 250. Calculate the magnetizing current, core losses and the maximum value of flux in the co..

  Calculate the energy generated by the electric machine

a. The mass of an electric car is 900 kg including the passengers. A single motor mounted on the front wheels drives the car, and the radius of the wheel is 0.3 m. The car is going downhill at a speed of 50 km/hr, and the slope of the hill is 30 d..

  Determine amplitude of the output for each of input signal

The input signal (inflow minus outflow) to an integral process varies sinusoidally at a radian frequency, omega i. of 0.025 rad/s. The output signal varies sinusoidally at the same frequency with an amplitude of 10%.

  Design a short circuit stub matching circuit to match load

(a) ZL = 80+j60 , what is the load reflection coecient. (b) Design a short circuit stub matching circuit to match the load to Z0 of 50-ohms. State the distances in wavelengths and in centimeters.

  Compute the propagation constant and intrinsic impedance

Consider a plane wave normally incident on a half-space of copper. If f=1GHz, compute the propagation constant, intrinsic impedance, and skin depth for the conductor. Also compute the reflection and transmission coefficients

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd