User Account

All Pages

Find the position and magnitude of the balance mass

Assignment Help Mechanical Engineering
Reference no: EM13963882

Four masses m1, m2 , m3 and m4 are 200 kg, 300 kg, 240 kg and 260 kg respectively.

The corresponding radii of rotation are 0.2 m, 0.15 m, 0.25 m and 0.3 m respectively and the angles between successive masses are 450 , 750 and 1350.

Find the position and magnitude of the balance mass required , if its radius of rotation is 0.2 m.

Reference no: EM13963882

Questions Cloud

Find agnitudes and angular positions : The balancing masses are to be placed in planes X and Y. The distance between planes A and X is 100 mm, between X and Y is 400mm and between Y and D is 200mm. If the balancing masses revolve at a radius of 100mm, find their agnitudes and angular p..
Should such speech also be banned in the internet : You cannot advocate lawlessness in a speech said in the middle of the street. Yet, it would seem that right now our busiest "street" is the Internet. Should such speech also be banned in the Internet
What makes the sound of a violin different : How can Lissajous patterns be used in checking out specific frequencies (such as in tuning a piano)? What makes the sound of a violin different from that of a piano when they are playing the same note?
Does thermal energy flow from hot to cold or vice-versa : In the operation of a refrigerator, does thermal energy flow from hot to cold, or is it from cold to hot? Why?
Find the position and magnitude of the balance mass : The corresponding radii of rotation are 0.2 m, 0.15 m, 0.25 m and 0.3 m respectively and the angles between successive masses are 450 , 750 and 1350 - Find the position and magnitude of the balance mass required , if its radius of rotation is 0.2 m..
Determine the power developed : Determine the power developed, the total percentage fluctuation of speed and the angular acceleration of flywheel when the crank has rotated thro' an angle of 600 from the Inner dead centre
Gender and according to the choice of their major : A random sample was taken of 300 undergraduate students from a university. The students in the sample were classi?ed according to their gender and according to the choice of their major. The result is given in the following table.
Find the beat frequency of the combined waves : Two sound waves are emitted: y1, with frequency f1, and y2, with frequency f2, with other constants identical, as expressed below. Distances in meters, times in seconds, and angles in radians: y1 = .02 sin(8 Pi x - 108 Pi t) (2) y2= .02 sin (8 Pi x..
Write equations of motion for the system : A 50 kg crate slides down a 6 m ramp inclined at an angle of 35 degrees to the horizontal. A worker pushes on the crate parallel to the ramp so that it slides down with a constant velocity. If the coefficient of kinetic friction is .33

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the angle through which end d of shaft cd rotates

In the gear-and-shaft system shown, the shaft diameters are dab= 2 in. and dcd=1.5 in. Knowing that G = 11.2 x10^6 psi, determine the angle through which end d of shaft cd rotates.

  Find a total strain corresponding to yield strength b what

in a tensile test for an alloy used for ballistic-missile launch tubes on boomer submarines the yield strength was

  An air conditioner operating at steady state maintains a

an air conditioner operating at steady state maintains a dwelling at 20 degrees celsius on a day when the outside

  The convection heat transfer coefficient in the furnace is

in an annealing process a stainless steel plate 50 mm thick will be heated to at least 600degc from an initial

  Determine the velocity of an airstream in a wind tunnel

The proposed design for anemometer to determine the velocity of an airstream in a wind tunnel is comprised of a thin metallic strip whose ends are supported by stiff rods serving as electrodes for a passage of current used to heat the strip.

  Consider a cubic crystal with the lattice constant

Consider a cubic crystal with the lattice constant a.Sketch the unit cell with the crystallographic planes having Miller indices (011) and (033). What is the spacing d between these two parallel planes? Explain your answer. Include additional sketche..

  An automotive repair shop stock many sizes of tires one

an automotive repair shop stock many sizes of tires. one particular size and model is purchased for 15 and sold for 30.

  A rigid tank containing 20 kg of refrigerant 134a as

a a rigid tank containing 20 kg of refrigerant 134a as saturated vapor at 1.0 bars and -26.43 c is heated until the

  A golfer hits a golf ball with an initial velocity of 160

a golfer hits a golf ball with an initial velocity of 160 fts at an angle of 25deg with the horizontal. knowing that

  If these viscosities are the safe limits for the oil

a pump fitted with 50mm bore ball bearings uses an oil whose viscosity ranges from 100cst at cold pump start-up to

  Write the differential equation and identify the boundary

consider a one-dimensional plane wall of thickness 2l. the surface at x -l is subjected to convective conditions

  Two blocks of steel cp011 btulbm ordmf one at 800ordmf and

two blocks of steel cp0.11 btulbm ordmf one at 800ordmf and the other at 300ordmf are brought into contact in an

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd