Find the number of teeth in each gear

Assignment Help Mechanical Engineering
Reference no: EM131378999

Two gears with a module of 2 mm are mounted at a center distance of 130 mm in a 4 : 1 ratio reduction gear set. Find the number of teeth in each gear.

Reference no: EM131378999

Questions Cloud

Define the elements of a stop and frisk : Define the elements of a stop and frisk, as well as the requirements of a stop and frisk - Outline the facts and findings of Floyd v. the City of New York.
What are total return and capital gains for discount bond : FIN-534- What are the total return, the current yield, and the capital gains yield for the discount bond in Question #3 at $887.00? At $1,134.20?
Did kelco have a claim against the bank : Later, Kelco discovered that her bank had not stopped payment on the cashier's check and instead had paid it. Did Kelco have a claim against the bank? Explain.
Did the bank violate its duty to stop payment on the check : Thirteen months later, the check turned up, and Granite's bank paid it. Did the bank violate its duty to stop payment on the check? Explain.
Find the number of teeth in each gear : Two gears with a module of 2 mm are mounted at a center distance of 130 mm in a 4 : 1 ratio reduction gear set. Find the number of teeth in each gear.
May a bank honor a check when it knows of death of drawer : She deposited it in her bank account. Norris died before the check cleared, and his bank refused to pay it. May a bank honor a check when it knows of the death of the drawer? Explain.
List and describe the six categories of needs to consider : FIN 3660- List the 5 steps in the recommended procedure to estimate a person's monetary value for the purpose of life insurance. List and describe the six categories of needs to consider in determining the amount of insurance a person should carry.
Did the drawee bank violate a duty it owed to templeton : It kept the check until June 28, when it returned it to Templeton with the notification that payment had been stopped. Did the drawee bank violate a duty it owed to Templeton? Explain.
Could stewart sue the bank for refusing to honor the check : The bank acknowledged that the check was good, that is, that there were sufficient funds in the account. Could Stewart sue the bank for refusing to honor the check? Why or why not?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The acceleration of a particle traveling along a straight

the acceleration of a particle traveling along a straight line is a8-2s ms2 where s is in meters. if v0 at s0 determine

  Method for constructing concrete foundation walls

The elements of a new method for constructing concrete foundation walls for new houses - design exercise, make a conservative estimate for the uniform tie spacing d if the tension in each tie is not to exceed 6.5 kN.

  A freight elevator moving upward with a constant velocity

a freight elevator moving upward with a constant velocity of 6fts passes a passenger elevator which is stopped. four

  A simple steam power system has a turbine inlet state of 60

a simple steam power system has a turbine inlet state of 6.0 mpa and 540 0c and an exhaust pressure 0.008 mpa. the

  1000 ft3min of air at 50 degrees fahrenheit dry-bulb and

1000 ft3min of air at 50 degrees fahrenheit dry-bulb and 95 relative humidity are mixed with 1500 ft3min of air at 76

  A horizontal aluminum rod 1 cm in diameter and 10 cm long

a horizontal aluminum rod 1 cm in diameter and 10 cm long has both ends maintained at 363 k. air at 293 k and 1 atm

  A hot wire anemometer is a device to measure the velocity

a hot wire anemometer is a device to measure the velocity of a flow of air. it consists of a thin cylindrical wire in

  Descriptive questions - give brief answers in words no

descriptive questions - give brief answers in words. no calculations are required. you may write your answers in point

  Calculate the difference between the strain at failurelet

al 6061-t6 bar. properties youngs modulus e 68300mpa yield strength sigmay 276 mpa ultimate strength sigmau 310mpa

  Determine torque and power required to rotate inner cylinder

The space between two 6 in. long concentric cylinders is filled with glycerin (viscosity = 8.5X10-3 lb s/ft2). The inner cylinder has a radius of 3 in. and the gap width between the cylinders is 0.1 in. Determine the torque AND power required to rota..

  Determine an expression for the fundamental axial mode shape

Determine an expression for the fundamental axial frequency of the bar (ω rad/s). Your answer should contain the parameters λ, p, and L.

  Calculate the reynolds number of the flow

Carbon dioxide with a specific weight of 0.114 lb/ ft3 and a dynamic viscosity of 3.34 x 10-7 lb-s/ ft2 flows in the shaded portion of the duct shown in Fig. 9.17. If the volume flow rate is 200 ft3 / min, calculate the Reynolds number of the flow.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd