Find the metacentric height for rotation

Assignment Help Mechanical Engineering
Reference no: EM131395095

A barge is of rectangular section of 26.7 m × 10 m and is 3 m in height. The mass is 453.62 tons with load. The centre of gravity is at 4 m from bottom. Determine the metacentric height for rotation along the 26.7 m centreline. Investigate the stability. Also determine the restoring torque if it is rotated by 5° about the axis.

Reference no: EM131395095

Questions Cloud

Form of argumentation - christmas is always on a thursday : Determine whether the following arguments are inductive or deductive.- Since Christmas is always on a Thursday, it follows that the day after Christmas is always a Friday.
Find the tension in the chain : A sphere of 1.25 m dia floats half submerged in water. If a chain is used to tie it at the bottom so that it is submerged completely, determine the tension in the chain.
Page paper about diversity : Write a 4 to 6 page paper about Diversity using APA style. Note that 4 to 6 pages means 4 to 6 pages of double-spaced written material with 1-inch margins left, right, top and bottom, and Times New Roman, 12-point font. (a) a narrow, carefully c..
What are managements and labors responsibility to achieve : If labor and management cannot reach an agreement, then they may use the following tactics: strike, lockout, boycotts, work slowdown, and corporate campaigns. Describe at least two tactics. Which one do you think would be most successful today and..
Find the metacentric height for rotation : The centre of gravity is at 4 m from bottom. Determine the metacentric height for rotation along the 26.7 m centreline. Investigate the stability. Also determine the restoring torque if it is rotated by 5° about the axis.
Form of argumentation - triangle having two equal angles : Determine whether the following arguments are inductive or deductive.- Suppose figure A is a triangle having two equal angles. It follows that figure A has two equal sides.
Discuss the impact of health policies on health services : In 100 words or more, discuss the impact of health policies on health services in terms of the money, human resources, and technology used to produce these services. Your answer should include a discussion on each of the three areas.
Consider the nonverbal messages surrounding the message : Look at a business letter that you have received at work or at home. Consider the nonverbal messages surrounding the message. Do they support the verbal message or not? If not, what could the sender have done to ensure that the verbal and nonverba..
Form of argumentation - baked brownies : Determine whether the following arguments are inductive or deductive.- By accident Karen baked her brownies two hours longer than she should have. Therefore, they have probably been ruined.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Elastic modulus of a composite

Carbide cutting tools are composites of very hard tungsten carbide particles   in a cobalt matrix. The elastic moduli of tungsten carbide and cobalt are 102 × 106  and 30 × 106  psi, respectively. It was experimentally found that the elastic modul..

  Hemispherical end caps are welded to a cylindrical main

hemispherical end caps are welded to a cylindrical main body to form a propane storage tank. the tank has an inside

  Steady-state heat transfer situation

A dormitory at a large university, built 50 years ago, has exterior walls constructed of Ls = 25-mm-thick sheath- (a) Show the thermal circuit representing the steady-state heat transfer situation. Be sure to label allelements, nodes, and heat rates...

  Coefficient of friction between the band and the pipe

The coefficient of friction between the band and the pipe is 0.30, and that between the pipe and the block is 0.40. The weights of the parts are negligible.

  There is much consternation between your associates as to

a closed tank having a volume of 2ft3 is filled with 0.30 lb of a gas. a pressure gage attached to the tank reads 12

  Write out transformation formula for a fifth order tensor

Write out the transformation formula for a fifth order tensor. - Show that the sum of the squares of the elements of a tensor is an invariant.

  Hydraulic pressure, piston velocity

A pump supplies oil at 20 lpm to a 50 mm diameter double acting cylinder. If the load is 500 kg(extending and retracting) and the rod diameter is 25 mm,

  Determine the moment of the force f of magnitude

The crank of Prob. 2/10 is repeated here. If OA = 50 mm, () = 25°, and f3 = 55°, determine the moment of the force F of magnitude F = 20 N about point O.

  Law of parallelogarm forces

To finding in Law of parallelogarm forces We take Q sin? (Along Vertical Side) & Q cos? (Along Horizontal Side)

  An engineer is making an estimate for a home owner this

an engineer is making an estimate for a home owner. this owner has a small stream of water q1.4cfs t40cthat is located

  Refrigerator operates at steady a coefficient of

refrigerator operates at steady a coefficient of performance of 5.0 within a kitchen at 238c. the refrigerator rejects

  If the work during the process is 300 kj determine a the

water in a piston-cylinder assembly initially at a temperature of 100oc and a quality of 65 is heated at constant

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd