Find the maximum thermal efficiency of this heat engine

Assignment Help Mechanical Engineering
Reference no: EM13629805

You have a heat engine that has a thermal energy resevoir available at 500C, the thermal energy to heat the engine is at a maximum rate of 20 kW. The sink of the engine is 20C, the power output required from the engine is 16kW. A) find the maximum thermal efficiency of this heat engine (62.1%). B) Determine whether this engine can produce its desired power output (no).

 

Reference no: EM13629805

Questions Cloud

A round casting is 01 m in diameter and 5 m in length what : a round casting is 0.1 m in diameter and .5 m in length. another casting of the same metal is elliptical in
The distribution of the sum of independent n 2 random : the distribution of the sum of independent n? ?2 random variables isa. always approximately normalb. always exactly
Write down the pdf for each of the following distributions : write down the pdf for each of the following distributions then sketch the distributions on the axes provided be sure
Two parallel infinite nonconducting plates are 106 cm apart : two parallel infinite nonconducting plates are 10.6 cm apart and have charge distributions of 2.5 microcm2 and -2.5
Find the maximum thermal efficiency of this heat engine : you have a heat engine that has a thermal energy resevoir available at 500c the thermal energy to heat the engine is at
Mcdonalds waiting times you want to estimate sd for the : mcdonalds waiting times. you want to estimate sd for the population of waiting times at mcdonalds drive up windows. you
Mrs smiths reading class can read an average of 175 words : mrs. smiths reading class can read an average of 175 words per minute with a standard deviation of 20 words per minute.
Calculate the standard deviation for the following sample : calculate the standard deviation for the following sample and show your work. use the formula of your choice. use the
The probability that a radish seed will germinate is 07 the : the probability that a radish seed will germinate is 0.7. the gardner plants 140 seeds what is the probability that she

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Find the change in diameter of a cylinder

how to find the change in diameter of a cylinder of 225mm length, 25mm diameter and a load of 180Km?

  Determine the phase or phases in a system

Determine the phase or phases in a system consisting of H2O at the following conditions and sketch p-v and T-v diagrams shown the locations of each state?

  Its surface temperature is 230 0c and the ambient air

a large fireplace in a ski lodge has a glass firescreen which covers a vertical opening in the fireplace. the opening

  A symmetrical wedge having a total vertex angle of 60

a symmetrical wedge having a total vertex angle of 60 degrees is traveling at mach number of 3 at an altitude of 15 km.

  Find the stoichiometric air/fuel ratio of benzene

Please find the stoichiometric air/fuel ratio of benzene (C6H6) and the actual air fuel ratio when operated at equivalance ratio of 0.8.

  If the nozzle outlets are exposed to atmospheric pressure

in a hydroelectric power plant water enters the turbine nozzles at 800 kpa absolute with a low velocity. if the nozzle

  It is assumed that the wire surface temperature is constant

an electrical wire having a diameter of 1.5 mm and covered with a plastic insulation thickness 2.5 mm is exposed to

  Determine the blade angles at leading

(a) Determine the blade angles at leading and trailing edges of both the rotor and stator at the mean radii, (b) Calculate the mass flow rate and the power required for each stage.

  Determine the largest couple moment m

The uniform 6-kg slender rod rests on the top center of the 3kg block. If the coefficients of static friction at the points of contact are ua=.4 and ub=.6, and uc=.3, determine the largest couple moment M which can be applied to the rod without ca..

  A 20 mm id steel tube carries liquid at 10 mpa assume that

a 20 mm id steel tube carries liquid at 10 mpa. assume that the tubing is very long. determine the principal stresses

  A piston-cylinder device initially contains 007m3 of

a piston-cylinder device initially contains 0.07m3 of nitrogen gas at 130kpa and 120 degrees celsius. the nitrogen is

  Calculate the work done during the process determine the

a piston-cylinder device initially contains 1.2 kg of steam with a volume of 0.2 m3. the mass of the piston is such

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd