Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
A circuit operating in the sinusoidal steady state has two exposed terminals a and b. The phasor voltage Vab in the circuit is 480 /0° V (rms) when no external load is connected to terminals a,b. When a load having an impedance of 100 j0 Ω is connected across a,b, the value of Vab is 252.9822 /-18.3449° V (rms).
a) Find the impedance that should be connected across a,b for maximum average power transfer.
b) Find the maximum average power transfer to the load of (a).
A thermal oxide of thickness 120 nm needs to be grown on a silicon wafer (100) in dry oxygen. If the process integration issue requires having a temperature not higher than 1050 degreeC, determine the time required to obtain the desired thickness.
Design a DC power supply that provides -95v +/- 5v to a 2 amp load (energy absorber). The input source is a 100 volt peak sinusoid, 60 Hz. You may use any basic circuit element. State the values of all circuit elements (in ohms, farads, etc).
(TCO 6) The operation B + A is being performed with B = 0 and A = 1. According to the rules of addition for binary numbers, which should the result be for CO and SUM?
A meter stick is found to balance at the 49.7-cm mark when placed on a fulcrum. When a 60.0-gram mass is attached at the 27.0-cm mark, the fulcrum must be moved to the 39.2-cm mark for balance.
The respective resistance measurements (from the first bar) are 11.1 kW, 12.1 kW, and 14.5 kW.Find the a) material resistivity and b) contact resistivity, then c) restate the material resistivity as a sheet resistivity.
The desired signal at the output of the amplifier is 10 dBm, and the signal level applied to the fiber connector at the head end is 10 dBm. What should the gain of the amplifier be to have 10 dBm at the output of the neighborhood amplifier
A)Design a high-pass filter with a cutoff frequency of 40 kHz. Use 0.01 uF capacitor and an appropriate resistor. B) Sketch and label the circuit. C) What is the gain of the filter at the cutoff frequency Give your answer both as ratio (Vout/Vin) ..
In Mips when you use addi or any other commands in which you use a 16 bit value for a reg. value or address offset what operation is done to check if its is a negative number's two's complement or just a regular binary number
Consider a source-free parallel RLC circuit having alpha =10^8 s^-1, omega-sub-zero = 10^3 rad/s, and omega-sub-zero * L = 5 ohm. a) Show that the stated units of omega-sub-zero * L are correct. b) Compute s_1and s_2.
Notice that when C begins sending, the signal due to the frame from A has not reached station C yet. If it reached, station C would not send it. How many bits from station C have already been sent when it hears the signal from A
Two balanced three-plia.se loads that are connected in parallel are fed by a three-phase line having a series impedance of (0.4 + j2.7) ohm per phase. One of the loads absorbs 560 kVA at 0.707 power factor lagging
Design a circuit using a thermister in a Wheatstone bridge and a comparator to turn on a furnace when the temperature drops below 70 ?F. Use real components selected from an online distributor, such as Digi-Key or Mouser
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd