Find the mass and volume of air in the cylinder when

Assignment Help Mechanical Engineering
Reference no: EM13626415

NINE kg of AIR is initially contained in a rigid tank at 1000 kPa and ONE kg of AIR occupies space in a piston-cylinder device. The valve in the Air Tank pipe connecting the tank to the cylinder is accidentally bumped slightly open causing air to slowly leak from the tank to the cylinder. The heavy piston moves freely (without friction) as shown. The process occurs slowly enough that there is sufficient heat transfer to maintain a uniform and constant temperature of 300 K. Neglect changes in kinetic & potential energy of the air. The surrounding atmospheric pressure is 100 kPa. Given: piston weight = 120 kN, area = 0.60 m2.

FIND: The mass and volume of air in the cylinder when equilibrium is finally achieved and the total heat transfer required, QIN (kJ). NOTE: Complete a p-V diagram, fill out a property table and clearly show your analysis.

Reference no: EM13626415

Questions Cloud

A 6-lb block is attached to a cable and to a spring : a 6-lb block is attached to a cable and to a spring vertically the cable above and the spring below. the spring
On a beautiful standard day your oceangraphic ship sights a : on a beautiful standard day your oceangraphic ship sights a water spout in the ease indian ocean. you fix your position
What is the balls maximum acceleration what is the balls : a 120 g ball attached to a spring with spring constant 2.9 nm oscillates horizontally on a frictionless table. its
Methane at 77 f 1 atm enters an insulated reactor operating : methane at 77 f 1 atm enters an insulated reactor operating at steady state and burns with the theoretical amount of
Find the mass and volume of air in the cylinder when : nine kg of air is initially contained in a rigid tank at 1000 kpa and one kg of air occupies space in a piston-cylinder
The minimum stopping distance for a car traveling at a : the minimum stopping distance for a car traveling at a speed of 30msand is 60 m including the distance traveled during
Carbon monoxide at 77f 1 atm enters and insulated reactor : carbon monoxide at 77f 1 atm enters and insulated reactor operating at steady state and burns with air entering at 77 f
The star s0-2 of spectral class b1 v orbits the central : the star s0-2 of spectral class b1 v orbits the central black hole at the galactic center on an orbit with a semimajor
The airplane is cruising at m023 with an angle of attack : a flying wing has a swept symmetric airfoil with a planform area of 3700 sq ft a root cord at the airplane centerline

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd