Find the least time that will take passengers from a stop

Assignment Help Mechanical Engineering
Reference no: EM13623126

The Elevator An express elevator is to carry passengers from ground level to a lobby where they can catch elevators to higher floors. This express trip is 80m of vertical rise. The constraints for the design are, 1) that the acceleration cannot change by more than +- 1.5 m/s^3; that is the jerk is limited to +-1.5 m/s^3; and 2), that the acceleration itself should never exceed +-1.5 m/s^2; and 3) that the velocity should never exceed +-5 m/s. Find the least time that will take passengers from a stop on the ground floor to a stop at the lobby. Determine the piecewise function that describes velocity during an ascent.

Reference no: EM13623126

Questions Cloud

Jessica wants to accumulate 15000 by the end of 6 years in : jessica wants to accumulate 15000 by the end of 6 years in a special bank account which she had opened for this
Suppose a loaf of bread cost 100 in 1984 and 180 in 2004 : suppose a loaf of bread cost 1.00 in 1984 and 1.80 in 2004. what is the bread price index in 2004 using 1984 as the
At a time of 160 s after she enters the water her speed is : a 64.0 kg person standing on a diving board dives straight down into the water. just before striking the water her
A recent survey asked adults about their beliefs about : a recent survey asked adults about their beliefs about premarital sex and whether they thought birth control should be
Find the least time that will take passengers from a stop : the elevator an express elevator is to carry passengers from ground level to a lobby where they can catch elevators to
Over the past five years a stock produced returns of 11 : over the past five years a stock produced returns of 11 percent 14 percent 4 percent -9 percent and 5 percent. what is
A stock is currently trading at 50 the continuously : a stock is currently trading at 50. the continuously compounded interest rate is 10. a call option with 6 month
A single square loop of wire 237 cm on a side is placed : a single square loop of wire 23.7 cm on a side is placed with its face parallel to the magnetic field between the pole
The accounting manager of gateway inns has noted that every : the accounting manager of gateway inns has noted that every time the inns average occupancy rate increases by 5 percent

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Construct a 90 two-sided confidence interval on mean life

the service life of a battery used in a cardiac pacemaker is assumed to be normally distributed. a random sample of 10

  You are an industrial hygienist for a large distributor of

you are an industrial hygienist for a large distributor of industrial compressed gases who was evacuated to baton rouge

  The desiggn calls for air entering the dehumidifier to be

the boss asked you to size a dehumidifier to dehumidify 100lbm per hr of air. the desiggn calls for air entering the

  The accompanying table provides additional data at the two

five kg of water contained in a piston cylinder assembly expand from an initial state where t1400 degree celsius p1700

  Find out the largest couple that can be applied

Determining the largest couple that can be applied to a beam in pure bending. A beam of cross section shown is extruded from an aluminum alloy for which σy = 310 MPa and σu = 480 MPa.

  On a given day a barometer at the base of the washington

on a given day a barometer at the base of the washington monument reads 29.97 in. of mercury. what would the barometer

  Assume that 350 kjkg of energy must be removed by heat

for each kw of power input to an ice maker at steady state determine the maximum rate that ice can be produced in kgs

  An exit air bulk average temperature t bo 127 0c is

air at 1.0 atmosphere pressure and 77 0c enters a 5.0 mm i.d. tube with a bulk average velocity of 2.5 ms. the velocity

  A copper-clad steel sheet is produced by hot roll bonding

a copper-clad steel sheet is produced by hot roll bonding. the cladding separated during deep drawing. what are some

  Explain temperature effect on materials

Temperature Effect on Materials (i) A hollow cylinder of aluminium 1 m long with a 40 mm outside diameter is at a temperature of 20 °C. What is the change in length and circumference of the cylinder when it is cooled to â?'25 °C

  Deternine the duct length required to reach mach 06

air flow enters a constant-area insulated duct with a mach number 0.2. the duct diameter is 10 mm and the friction

  A solar hot-water system stagnates at 85 c under

a solar hot-water system stagnates at 85 c under insolation of 740 wm2 and an ambient temperature of 17 c. find its

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd