Find the internal forces as the nut is rotated 1 turn

Assignment Help Civil Engineering
Reference no: EM13302405

A steel bolt and nut are tightened around an aluminum sleeve. Find the internal forces as the nut is rotated 1 turn

Reference no: EM13302405

Questions Cloud

How much error would there be in the volume calculation : Assume the actual water temperature for calibrating a 1/3 ft3 measure was 65 degrees F. If you had used a water temperature of 75 degrees F for your calibration, how much error would there be in your volume calculation (both in ft3 and as a percen..
Ethical implications : Think of a situation that you have experienced or heard about that might be seen as having ethical implications.
State concentration of co3^2- need to initiate precipitation : What concentration of CO3^2- is need to initiate precipitation. Neglect any volume changes during the addition.
How far apart is this bright band from the central peak : Two slits are illuminated by a 390 nm light.The angle between the zeroth-order bright band at the center of the screen, how far apart is this bright band from the central peak
Find the internal forces as the nut is rotated 1 turn : A steel bolt and nut are tightened around an aluminum sleeve. Find the internal forces as the nut is rotated 1 turn
With what speed must she jump to escape the asteroid : A fully suited 100 kg astronaut stands on a spherical asteroid of diameter 1.0 km and mass 2.5 x 1012 kg. With what speed must she jump to escape the asteroid
Determine the speed of the car when s starting from rest : The 2 Mg car is being towed by a winch. If the winch exerts a force of T=105s on the cable, where 14m is the displacement of the car in meters, determine the speed of the car when s , starting from rest. Neglect rolling resistance of the car.
Calculate the mass of ammonium added to 1 l of water : Ammonium (NH4+) is a weak acid with a pKa of 9.26. The dissociation is: NH+4 NH3 + H+. Calculate the mass of ammonium added to 1 L of water in order to obtain a pH of 4 at equilibrium.
Compute what is the percent yield of the reaction : Assuming ideal gas behavior, calculate the mass of (in ) present in the reaction mixture at equilibrium. What is the percent yield of the reaction under these conditions

Reviews

Write a Review

Civil Engineering Questions & Answers

  Which would require less wood and by what percentage

An engineer is to design a channel lined with planed wood to carry 2 m3/s of water on a given slope. The channel cross section can be either a 90 degree triangle or a square. Which would require less wood and by what percentage

  Find the maximum axial tension using lrfd

No incisions are noted. Find the maximum axial tension using LRFD. Can we resist the same force in compression if the member is 10ft long?

  Estimate how often it will take more than 75 min to repair

Data from service records show that the time to repair a certain machine is normally distrubuted with a mean of 65 min and a standard deviation of 5 min. Estimate how often it will take more than 75 min to repair a machine.

  Find contact time would be reuired for inactivating giardia

How much contact time would be reuired for inactivating Giardia cysts using the following chemicals at the concentrations and temperatures stated: a. Chlorine Dioxide, 23C, 1.0 mg/L b. Chlorine, 12C, 1.6 mg/L c. Ozone, 10C, 5 mg/L d. Chloramines, ..

  Depth of aggregate of wheel load over soil

A 2000-lb wheel load is to be supported by aggregate over soil with a maximum bearing pressure of 1000 lb/sqft. What depth of aggregate is needed if the angle theta is 40 degrees?

  Elevation of the road at station

Given the following data for a vertical curve of a road; G1=-2.5%, G2=+5.5% and station of PVI=250+50.At station 252+50, the vertical curve must intersect an existing road at elevation 48.48ft. the elevation on the tangent section at station 256+5..

  Problem of coefficient of static friction

The machine part ABC is supported by a frictionless hinge at B and a wedge at C. Knowing that the coefficient of static friction is 0.20 at both surfaces of the wedge, determine:

  Determine at which of the two points the elevation is higher

At point 2, the velocity and pressure are 14 ft/s and 23 psi. Determine at which of these two points the elevation is higher. Calculate the height difference. (Assume the sp ecific gravity of butane is 0.6 and that the butane is at a temperature o..

  Derive an equation for concentration of a chemical in a lake

Account for chemical reactions, groundwater flows, streams, precipitation, evapotranspiration. Indicate any assumptions that can be made to simplify your equation.

  Design the roof slab as a one-way slab system

Design the roof slab as a one-way slab system and use the worst case design scenario to determine the reinforcing for the entire roof

  Determine total stress and pore water pressure of sand

a layer of clay, 5m thick, overlies a deposite of sand, 5m thick, which is underlaid by rock. the water table in the sand is sub-artesian with a level at 2m below fround level. the saturated unit weights of the clay and sand are 21 and 16 KN/m^3 r..

  What should be the new volume of the lake

Suppose that the distance from the lake outlet to the withdrawal cannot be more than 20 mi. What should be the new volume of the lake?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd