User Account

All Pages

Find the initial torque supplied to the antenna

Assignment Help Electrical Engineering
Reference no: EM131372987

Assignment

1.) Assume that Figure 11.25(a) is the response curve of a control system to a step function. Determine the following parameters: rise time, overshoot, and settling time.

2.) A robot arm was commanded to go to a new position. Its response was recorded and is shown in Figure 11.41. Determine the rise time, overshoot, settling time, and steady-state error of the response, approximately.

3.) In your own words, explain the principle of proportional control

4.) A proportional controller for a rotating antenna has a gain KP of 5 in · oz/deg. The antenna was initially pointing due south but was then commanded to point southeast.

a.) Find the initial torque supplied to the antenna.

b.) What is the torque when the antenna gets to within 5° of its set point?

5.) A proportional control system is to be used to control the wing flaps of a jet airplane. The wind load is expected to cause as much as 600 in · lb of torque. The system should be able to keep the flaps to within 5° of the set point. Find the gain KP necessary to meet the requirements.

6.) Explain how the addition of integral feedback in a proportional control system eliminates steady-state error.

7.) Explain how derivative feedback makes a control system more responsive to rapid change and how it reduces overshoot.

Reference no: EM131372987

Questions Cloud

What is the distribution of z : Suppose X∼U(0, 1) and Z = 3X + 5 what is the distribution of Z? Suppose X∼N(10, 25). What transformation formula should I use to get Z∼N(2, 36)
Check that the method only lists matching files : Check that the method only lists matching files. Also try it with a search string that matches none of the file names. Is anything at all printed in this case?
Prepare a presentation on the drug markets and consumers : Start with the week's required readings. Focus on those pieces of evidence and/or arguments that are important for understanding how to formulate or evaluate health policy in your case study area. the required reading .
Draft the strategic points for a potential dissertation : Consider a potential gap in the literature that is emerging from your ongoing reading in your field of interest including no less than five specific research studies.
Find the initial torque supplied to the antenna : ECET 402- Find the initial torque supplied to the antenna. What is the torque when the antenna gets to within 5° of its set point?
How might dating lead to sexual harassment : Do you agree that people who work together can date? How might dating lead to sexual harassment? Should organizations have policies about employee dating? If they have policies, what should the policies include?
Generation of peacekeeping does interfet represent : 1. Which generation of peacekeeping does INTERFET represent? Explain your answer.
Any other ideas on how to break the glass ceiling : Only a small percentage of Fortune 500 companies have female CEOs. One solution to increase the number of women CEOs would be a have co-CEOs, one male and one female. Do you think this would work? Do you have any other ideas on how to break the glass..
Meaningful information in a condensed format : The point of this assignment is to identify only the most important information to present. Avoid being vague. Instead, be specific, but succinct. The goal is to provide meaningful information in a condensed format.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Determine the required user signal power to achieve ber

In a multiuser CDMA system of DSSS, all transmitters are at equal distances from the receivers. The additive white Gaussian noise density Sn(f) = 5x10^-7 W/Hz. BPSK is used by all users with bit rate = 16 kb/s. There are 16 users.

  Find expression for torsional constant k in terms of moment

A thin metal disk of mass m=2.00 x 10^-3 kg and radius R=2.20cm is attached at its center to a long fiber. When the disk is turned from the relaxed state through a small angle theta, the torque exerted by the fiber on the disk is proportional to t..

  Draw a state diagram for an fsm with an input gcnt

draw a state diagram for an FSM with an input gcnt and three outputs x,y, and z. The xyz outputs generate a sequence called a Gray code in which exactly one of the three outputs changes from 0 to 1 or from 1 to 0.

  Develop equivalent circuits for the 741 as current amplifier

The 741 op amp is usually modeled on specification sheets as a voltage amplifier having the following parameters: Rin = 1 M, Av = 100,000, and Rout = 100  Using this information, develop equivalent circuits for the 741 as a current amplifier

  Find the even and odd components of the signal

http://www.transtutors.com/questions/find-the-even-and-odd-components-of-the-signal-list-the-values-of-the-signal-and-its-2082651.htm

  Calculate the length required for a 50% coupling

Calculate the length required for a 50% coupling when the gap is 7 μD.

  Determine what type of driving style is being used

.a. If the following voltage pulse is being applied to a stepper motor coil to the increment the shaft, what type of driving style is being used b. What advantage does this have as opposed to a constant-voltage pulase

  Find the probability of error in digital communication

A digital communication system transmits one of the three values -1,0,1. A channel adds noise to cause the decoder to sometimes make an error. The error rates are 12.5% if a -1 is transmitted, 75% if a 0 is transmitted, and 12.5% if a 1 is transmi..

  Obtain and simplify the flip-flop characteristic equations

The flip-flop input excitation equations are as follows: JA=XQ'B; KA=X'; JB=XQA; KB=X'Q'A The output equation: Z=XQAQB 1. Draw the circuit diagram 2. Obtain and simplify the flip-flop characteristic equations 3. Obtain the state table

  Determine the value of r resulting in maximum power

Determine the value of R resulting in maximum power to R and the maximum power to R.- Plot VR and IR versus R, and find the value of each under maximum power conditions.

  For the series parallel network of given figure determine i

For the series-parallel network of given figure: -  Calculate ZT. - Determine I.  -  Determine I1. -  Find I2 and I3. and  Find VL.

  Find the peak-to-peak value of the largest input signal

An amplifier with a power gain of 26 dB, is using a dual power supply of +/- 14 V. Find the peak-to-peak value of the largest input signal the amplifier can process without clipping.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd