Find the drag on the prototype blimp

Assignment Help Mechanical Engineering
Reference no: EM131279787

A new blimp will move at 6 m/s in 20 °C air, and we want to predict the drag force. Using a 1:13-scale model in water at 20 °C and measuring a 2500-N drag force on the model, determine

(a) the required water velocity,

(b) the drag on the prototype blimp and,

(c) the power that will be required to propel it through the air.

Reference no: EM131279787

Questions Cloud

Determine the estimated value of the company rv : Determine the estimated value of this Company RV, based on a relative value using the priceearnings ratio and the market value to book value ratio.
Do you feel that scientists should be cut out of the policy : Do you feel that scientists should be cut out of the policy making process, particularly on environmental issues, when their research is proven and widely accepted and is being ignored and disputed?
The dual problem have feasible solutions : Use the weak duality property to prove that if both the primal and the dual problem have feasible solutions, then both must have an optimal solution.
Equal employment opportunity commission : Which interviewing technique is less likely to involve discriminatory questions and, thus, be better supported by the Equal Employment Opportunity Commission (EEOC)?
Find the drag on the prototype blimp : A new blimp will move at 6 m/s in 20 °C air, and we want to predict the drag force. Using a 1:13-scale model in water at 20 °C and measuring a 2500-N drag force on the model
Procedure for valuation based on discounting cash flows : Why might an analyst prefer to use a measure of cash flow generating ability such as earnings instead of sales in relative valuation?
Evaluate the marketing management philosophy : Designs Limited is a fashion house operating in Kenya. They make fashionable designer clothes for women. Their outletss are located along Moi avenue, Ngong road, Mombasa road and at Ridgeways. Explain the overall positioning strategy used by G2 desig..
How does the leadership influence corporate culture : Let's discuss the best way for the CEO and top executives to lead a Corporate Culture. How does the leadership influence corporate culture? What happens when there is a change in leadership?
What other regular maintenance should be performed : Why is it important to continue auditing the bastion host? What other regular maintenance should be performed?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  High pressure and low pressure turbines are used

Reheat, where high pressure and low pressure turbines are used, is added to a simple steam cycle to increase the steam quality at the location where the steam exits the low pressure turbine and goes to the condenser. Consider a steam cycle where the ..

  Determine for the cycle the mass flow rate of steam

water is the working fluid in a regenerative rankine cycle with one closed feedwater heater and one open feedwater

  Compute all the stationary spot price equilibria

Compute all the stationary spot price equilibria, (x0 , x1, P , r , G, T), in which P = r = 1.

  Determine the magnitudes of r

The combined action of the three forces on the base at O may be obtained by establishing their resultant through O. Determine the magnitudes of R and the accompanying couple M.

  Specify the boundary conditions at 0degrees 180deg

consider the following single-dwell cam specificationrise segment 0 to 20 mm in 180 degreesdwell segment at 20mm

  A 3500 lb van is moving at 40 ftsec when it applies its

a 3500 lb van is moving at 40 ftsec when it applies its brakes which locks all four wheels. if the friction coefficient

  Explain change in magnetic properties when steel is heated

Explain the change in magnetic properties when steel is heated. Is this due to allotropic properties?

  What is the maximum allowable pressure

What is the maximum allowable pressure if a factor of safety of 4 is to be used and what pressure would a strain of 40 pc indicate?

  Determine and plot the required motor torque

Determine the moment MO of this tension about point O over the range 0 () 90°. Plot the x-, y-, and z-components of MO as functions of ().

  Gve the state temperature pressure quality if applicable

design a rankin cycle to analyze. the only restrictions are that water must enter the turbine as a superheated vapor

  The bottom wall of the channel is noticeably rough at a

considerr mach 2 flow in a twodimensional rectangular channel of length 5 m and height 1 m. the bottom wall of the

  The mark for water has risen 06 cm above the liquid-air

the density of a liquid is to be determined by an old 1cm diameter cylindrical hydrometer whose division marks are

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd