Find the distribution of internal forces n q and m

Assignment Help Mechanical Engineering
Reference no: EM131251901

The figure shows a two span simply supported beam, where the length of the inner beam AB is 4a, while the length of the cantilever beam BC is 2a. Vertical load 2P and P are acting on the middle of the beams AB and BC, respectively.

a) Determine the reaction components.

b) Determine the distribution of internal forces N, Q and M

1082_58c90610-c54e-4d56-9fb1-e9ed1fa29bb3.png

Reference no: EM131251901

Questions Cloud

What prevention or treatment are you researching : What prevention or treatment are you researching? What do the experts say? Is this a good strategy? Explain. Where did you get your information? Please provide the direct link.
Preliminary assessment of cost and price conditions : On a preliminary assessment of the cost and price conditions, the company finds that: The production cost of the new brand is expected to be much higher than that of TOUGH. Therefore the cost function of TOUGH is not relevant for SNOB.
Determine the reaction and bar forces : The figure shows a V-truss girder with a vertical load in B. All bars are elastic with stiffness EA.
Compute the reduction in excess burden : The combined federal and provincial taxes on a carton of 200cigarettes were reduced from $24 to $10 in February 1994. (a) Describe how you would compute the reduction in excess burden from the change.
Find the distribution of internal forces n q and m : The figure shows a two span simply supported beam, where the length of the inner beam AB is 4a, while the length of the cantilever beam BC is 2a. Vertical load 2P and P are acting on the middle of the beams AB and BC, respectively.
Calculate the yield to maturity : A: a 2 year coupon bond with a coupon rate of cA = 5 percent and pricedat PA(t) = $10, 000. B: a console with an annual coupon payment of $500 and priced atPD(t) = $10, 000. (a) Calculate the yield to maturity on each bond, ij , j = A, B,
Write the given assignment : Write the given assignment and I'm not sure what the teacher is requesting. - The assignment is to locate an article that would support the draft paper you are in the process of writing using Ohio Link.
Ricardian theory and with specific factors model : Compare and contrast the Heckscher-Ohlin theory with Ricardian theory and with specific factors model.
Choice of a discount rate : An analyst for a municipal public housing agency explained the choice of a discount rate as follows: "Our agency funds its capital investments through nationally issued bonds. The effective interest rate that we pay on the bonds is the cost that t..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Piston-cylinder assembly containing water

A piston-cylinder assembly containing water, initially a liquid at 500F, undergoes a process at a constant pressure of 20 lbf/in2 to a final state where the water is a vapor at 3000F. Kinetic and potential energy affects are negligible. Determine the..

  Align with two mounting holes in a steel plate

Two bosses in a plastic bezel must align with two mounting holes in a steel plate. The steel plate holes are 8 inches apart center to center. What should be the center to center distance of the core pins that make bosses of the plastic part?

  In order to determine the power dissipated across a

in order to determine the power dissipated across a resistor the current flow and resistance values are measured

  Plot the first order polynomial second order polynomian and

below is pressure measured at different timetime

  Isobaric cooling until a saturated vapor

A system consisting of 1 kg of H20 undergoes a cycle composed of the following closed process: Process1-2: Isochoric heating from P1= 5 bars, T1= 160 degrees Celsius to P2= 10 bars

  What heat removal flux can be achieved at the surface

What heat removal flux can be achieved at the surface of a horizontal 0.01 mm diameter electrical resistance wire in still 27?C air if its melting point is 927?C?

  What if the 820 kg car actually moves backwards with a

an 1640 kg car stopped at a traffic light is struck from the rear by a 820 kg car. the two cars become entangled moving

  Determine the velocity of point b, c, d, and e

Crank AB of the linkage shown rotates clockwise at 300 rpm. Using graphical method, determine the velocity of point B, C, D, and E.

  Plot wind speed against height on linear

for a neutral surface layer, plot wind speed against height on linear and on semi-log graphs for friction velocity of .5 m/sec and aerodynamic roughness length.

  Heat is required to raise temperature of water to boiling

You are throwing a dinner party and decide to prepare instant Chinese noodles (chicken flavor) for all your guests. From the cooking instruction on the back of the package, you determine that you will need to bring 50 cups of water to a boil for your..

  The pressure is held constant as the air cools to 50degc

consider the following setup that sits in a room with a surrounding temperature of 25degc. the pressure and temperature

  When the instrument is landed on mars the spring extends

an instrument to measure the acc. of gravity on mars is made of a spring from which hangs a mass of 0.24 kg. at a place

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd