Find the bearing life in hours for 90% reliability

Assignment Help Mechanical Engineering
Reference no: EM131377695

A No. 204 radial-contact ball bearing carries a combined load of 200 lb radially and 150 lb axially at 1200 rpm. The bearing is subjected to steady loading. Find the bearing life in hours for 90% reliability.

Reference no: EM131377695

Questions Cloud

Estimate the bearing life in hours for 90% reliability : Estimate the bearing life in hours for 90% reliability.
Can jones void the sale : On trial, it was proved that Smith actually did not know the stone was a diamond when he bought it, but he thought it might be a ruby. Can Jones void the sale? Explain.
Discuss about the sales force compensation : For companies that have a mission of selling, a major objective is to motivate the salespeople. While that are many factors that go into motivating these people, one of the primary factors is the compensation plan that describes how they will be ..
How victims can protect themselves from being victimized : Explain how victims can protect themselves from being victimized. Discuss when and where rates of victimization are the highest. analyze Victim Precipitation Theory and how the ideas contained therein can be applied to study of victimization.
Find the bearing life in hours for 90% reliability : A No. 204 radial-contact ball bearing carries a combined load of 200 lb radially and 150 lb axially at 1200 rpm. The bearing is subjected to steady loading. Find the bearing life in hours for 90% reliability.
Should deed declared invalid due to biggers undue influence : Joan was survived by two children and six grandchildren. Joan's children challenged the validity of the deed. Should the deed be declared invalid due to Biggers' undue influence? Explain.
Will a court grant gardner rescission of the contract : After discovering that the tavern's income was very low and that the tavern had very few female patrons, Gardner contacted Meiling's bookkeeping service and learned that the actual gross income for those three months had been approximately $1,400 ..
How you would use qualitative or mixed methods data analysis : Explain how you would use qualitative or mixed methods data analysis within your overall design. Explain how you would use these methods to enrich and explain anticipated findings from your evaluation design.
What happens to the energy lost by the reducer : Once the reducer reaches a steady state temperature, what happens to the energy lost by the reducer?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the acceleration of the block the velocity of the

a 250 kg block is pulled from rest along a rough surface by rope inclined 25 degree to horizontal. the tension in the

  Find the maximum tensile and compressive stresses

Find the maximum tensile and compressive stresses σt and σc, respectively, in the frame due to the load P= 8.0 kN if L= H = 1.4 m.

  It is pressurised internally until the outer layer surface

a thick cylinder has an inside diameter of 60 mm and an outside diameter of 100 mm. it is pressurised internally until

  Calculate the pressure if a u-tube manometer

Oil with S = 0.86 is being transported in a pipe. Calculate the pressure if a U-tube manometer reads 9.5 in. Hg. The oil in the manometer is depressed 5 in. below the pipe centerline.

  If the exit pressure is 200 kpa and the inlet volumetric

an air compressor is powered by a 2hp motor assume this is all input to the compressor. the inlet pressure and

  The discharge is located 20 ft 6 m higher than the entrance

500 galmin 30 ls of 100 degree f 40 degree c water flows through 300 ft 90m of 6-inch sch 40 steel pipe. the pipe

  Consider the air cooling system and conditions

Consider conditions for which there is a uniform heat transfer rate per unit length, qi'= 1.25 X 105 W/m, from the exhaust gases to the pipe inner surface, while air flows through the annular passage at a rate of  m· a = 2.1 kg/s.

  What is the total after-tax annual cost of the equipment

The equipment will provide a net value of £450 000 per year during the five-year period. Given that depreciation is declining balance, the after-tax ALARR is 20%, and the corporate income tax rate is 40%, what is the total after-tax annual cost of..

  Calculated on the basis of bond strength alone

Metals yield at a stress much lower than those calculated on the basis of their bond strength alone. This is explained by the presence of defects. Identify the principal defects responsible for this observation.

  C is to be 375 units and is to be directed at 75 degrees

resolve a vector a which has a magnitude of 50 units and a direction of 210 degrees into two vetors b and c. c is to be

  What wind velocity and barometric pressure

On a beautiful day your ship sights a water spout in the East Indian Ocean. You fix your position as 6000 ft from the spout and record a wind velocity of 10 ft/s. What wind velocity and barometric pressure does a fishing boat 600 ft from the spout ex..

  Calculate the overall heat transfer coefficient

Calculate the overall heat transfer coefficient (U) for the assumed tube diameter, fin shape and material. Use correlations to estimate hot-and cold-side convection coefficients, conduction resistance, contact resistance (if any), and fouling resi..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd