Find the armature current just after the power

Assignment Help Electrical Engineering
Reference no: EM131087090

A motor generates a CEMF at a rate of 0.5 V/100 rpm and has an armature resistance of 15 ?. Twelve volts are applied to the (stopped) motor. Find the armature current just after the power is applied and when the speed is 1500 rpm.

Reference no: EM131087090

Questions Cloud

Good decision on promotion effectiveness : Which Promotion is the best promotion for General Mills and which is the best for Safeway? Explain why? Based on what metrics? In the ideal world, what other data would you want to make a good decision on promotion effectiveness?
A maximum and the corresponding value of aoql : a. Calculate AOQ for p = .01, .02,..., .10. What does this suggest about the value of p for which AOQ is a maximum and the corresponding AOQL?
Self-fulfilling prophecy effects : Discuss how stereotyping, attribution, and self-fulfilling prophecy effects influence the perceptual process. Share a personal experience. The response should be at least 200 words in length.
Type of shared liability rules : Please explain who is liable on the contract to purchase purchase 100 gallons of milk from Jim (e.g., Nora, Henry, both). If you believe both Nora and Henry might be liable, please describe the type of shared liability rules applicable to them.
Find the armature current just after the power : Find the armature current just after the power is applied and when the speed is 1500 rpm.
Basic methods of control : Describe the nature of the control process. Identify its basic steps and the three basic methods of control. Understand the difference between bureaucratic, objective, normative, concertive, and self control.
Early management researchers : Briefly contrast two management theories and identify one of the early management researchers that contributed to each of these theories.
Calculate how much of each the consumer will demand : Econ 522 - Economics of Law - Calculate the consumer's demand, and his utility, in the absence of government intervention - How much revenue does the government raise with this tax?
Form of communication : The documentation you produce at work is intended as a form of communication. Explain what communication is and why it is important that the ideas/ information you communicate should be understood as they were intended (20-40 words)

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Give the range of addresses suitable for locating the code

A microcontroller memory map shows 16K bytes of Flash EEPROM in memory space $C000-$FFFF and 1 K bytes of RAM in memoryspace $1000-$13FF. a- Give the range of addresses (in hex) suitable for locating the code.

  Determine what is the motors full load efficiency

A 30hp 3 phase 360v 60 Hz induction motor has total internal losses of 2,500 watts when operating at full load. What is the motor's full load efficiency

  What is the rms voltage of the output noise

Gaussian white noise, perfectly band-limited to 0-10MHz, is passed through a perfectly rectangular filter of bandwidth 18 kHz, gain 3 dB, and center frequency 455 kHz. If the RMS voltage of the input noise is 1 volt

  What third resistor to create a voltage divider output of 10

two resistors with nominal values of 4.7K ohm and 10K ohm, are used in a voltage divider with a +15V supply to create a nominal +10V output. Assuming the resistor values to be exact, what is the actual output voltage produced

  Determine what mah capacity should the batteries have

A student project requires a 6 V DC power supply that can source 300 mA. The batteries for the power supply must last for a minimum of 8 hours of continuous operation. NiMH rechargeable batteries in AA size are to be used.

  Design a parameterized circuit

To instantiate a module within another module: Module_name instance_name #(parameter1 value, parameter 2 value, ...) (port1, port2, ...) ;

  Find the change in voltage for the current changes

1. Let Vi has a peak of 10v and R=1kOhm. Find the peak value of id and DC compoent V-o. 2. Consider a silicon diode with n = 1.5 Find the change in voltage if the current changes from 0.1 mA to 10 mA.

  List two advantages and disadvantages of having standards

When a system has permanent part and a removablepart(such as a CD-Rom and a CD-Rom), it is important that thesystem be standardized, so that different companies can make boththe permanent and removable parts and every thing still works together.

  Determine the transfer function for first-order high filter

Determine the transfer function for a first-order high filter with a cutoff frequency of 1000 radians per second and passband gain of 1 using the following types: a. 3-dB Butterworth type. b. Chebyshev type with 1 dB ripples on the passband.

  Find the steady state value of the output

transfer function: T(s)=1/(0.1s+1) with all initail conditions at 0 a) if the input is 1.5sin(2t)*u(t) find the steady state value of the output b) after the input is applied, approximately how long will it take for the steady state value you found i..

  Awheat stome bridge has following ab 20 ohm bc 24ohm cd

a wheat stome bridge has following ab 20 ohm bc 24ohm cd 5 ohm da 50 ohm bd 3 ohm. adca voltage source of 220v

  What types of legal liabilities should be considered

As a project manager on a product development team for a fast responding digital thermometer useable in high temperature applications (degrees C), you are asked to create a product development plan that addresses items

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd