Find the angles e1 and e2 make with the interface

Assignment Help Electrical Engineering
Reference no: EM13248152

Two homogeneous isotropic dielectrics meet on plane x=0. For x > 0, Er1=6 and for x<0, Er2=3. A uniform electric field E1=3ax-2ay+5az V/m exists for x >0. Find:

a) E2 for x<0
b) The angles E1 and E2 make with the interface
c) The energy densities in J/m3 in both dielectrics
d) The energy within a cube with side 1m centered at (1,2,3)

Reference no: EM13248152

Questions Cloud

Determine the average power consumption of the circuit : A series RCL circuit driven at angular frequency w = 780 rad/s has a capacitive reactance XC = 920 ohms, What is the average power consumption of the circuit
Determine the sum or difference of two numbers : Use the simulation timing diagram to compare the worse case time to do an operation with your ALU with the worst case using the 74LS381. State which operation takes the longest and list the time required for both ALU's.
What is the sale price at kitchen store : A competitor marked down the same set of pots 30%. Assume The Kitchen Store then reduces its selling price by 30% as well.
Define the vapor pressure of pure water : 173.3 g of NaCl completely dissolves (producting NA+ and Cl- ions) in 1.00 kg of water at 25.0 degrees celcius. the vapor pressure of pure water at this temperature is 23.8 torr. Determine the vapor pressure of the solution. A)19.3 torr B)23.8 tor..
Find the angles e1 and e2 make with the interface : Two homogeneous isotropic dielectrics meet on plane x=0. For x > 0, Er1=6 and for x 0. Find: a) E2 for x
Find the impedance of the circuit : A certain ac signal at 1000 Hz is applied across an inductor and a 100-ohm resistor. If the power factor of the circuit is 0.4, what is the impedance of the circuit
Find out the total number of valence electrons : Determine the total number of valence electrons in each of the following: a) SBr2; b)NBr3; c) CH3OH; d) NH4^+.
Explain and contrast the number of representative particles : Compare and contrast the number of representative particles and the mass of UF6 with the number of representative particles and mass of CCl3CF3. Explain any differences you observe.
Create successful organizational change : use the classroom resources, outside resources, and your personal experience to support your argument. Use APA format for your citations.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  How much stator referred external resistance per phase

How much stator referred „external? resistance per phase should be connected in the rotor

  Determine the vswr inside the transmission line

A N-turn resonant circular loop with a uniform current distribution and with a circumference of f/4 , is fed by a lossless balanced twin-lead transmission line with a characteristic impedance of 300 ohms. Neglecting proximity effects

  Calculate initial voltage that the capacitor charges to at t

An ideal voltage source produces a dirac delta function, an impulse spike to a series resistor, capacitor combination. R = 10.000 ohms, C = 0.039 uF. Calculate the initial voltage that the capacitor charges to at t = 0+.

  How a transformer works

How a transformer works and apply those rules to a transformer where the primary core cross-sectional area is twice.

  Determine what is the transistors emitter current

1) in a swamped common-emiter BJT amplifier, as shown below, if Vcc =12 V, R1 =8.2 kohm, R2=10 kohm, Rc = 500 ohm, Re= 1 kohm, Vbe = 0.7 V, and B =100, what is the transistor`s emitter current

  Define a design of a series controller

Design a series controller (a PD, PI or PID) so that the following performance specifications are satisfied. Steady-state error due to a step input = 0

  Develop the pseudo-code

Develop the pseudo-code below for a program that will retrieve 2 bytes (NUM1 and NUM2) from memory, determine which is closest to the numeric value 50, and indicate the result by setting a variable named "CLOSEST" to 1 (if 1st byte is closest) or ..

  What isthe minimum sampling frequency to avoid aliasing

a.) What isthe minimum sampling frequency to avoid aliasing b.)If the sampling frequency of fs=2500 samples/sec is used how many samples must be taken to give a frequency resolution of 10Hz

  What is the permeability of the relays magnetic circuit

The springs effect is addressed below. As a relay some contacts are connected to, and move with, the armature. Other contacts are stationary and would make or break contacts as the armature moves.

  Compute the signal voltage at the detectors output

20 SI fibers, 2 km long each, are spliced together for a 40 km link. Each fiber has a loss rate of 1-dB/km and a numerical aperture of 0.24. Each splice adds 0.5 dB of loss. A laser diode has a threshold current of 10 mA and emits at 3 mW/mA rate.

  What are the values of the rise time and response time

A thermometer, initially at a temperature of 75 degrees Fahrenheit is suddenly immersed into a tank of water with a temperature of 180 degrees Fahrenheit. The time constant of the thermometer is 4 s.

  How many bits to the left of binary point represent number

What fixed point unsigned representation, with how many bits and how many bits to the left of the binary point, should we use if we need to represent numbers in the range 0 - 100 with a resolution of .001 or better

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd