Find the acceleration of the block

Assignment Help Mechanical Engineering
Reference no: EM131382780

The block in given Figure is sliding down the inclined surface of a fixed wedge. This time the frictional force F exerted on the block is given by F = µN, where N is the normal reaction and µ is a positive constant.

Find the acceleration of the block. How do the cases µ < tan α and µ > tan α differ?

2470_Figure 9.jpg

Reference no: EM131382780

Questions Cloud

What is the instantaneous tension in the connecting string : The tension in the tow rope is suddenly increased to 4T0. What is the instantaneous acceleration of the blocks and what is the instantaneous tension in the connecting string?
Find the tension in the rope at a distance z below o : Find the tension in the rope at a distance z below O. The point of support now begins to rise with acceleration 2g. What now is the tension in the rope?
How much you will pay for the bond if you purchased the bond : Assume that today's date is April 15, 2015. Fresh Bakery Inc. bond is an annual-coupon bond. Par value of the bond is $5,000. How much you will pay for the bond if you purchased the bond today?
Show that they will collide in less than 425 s : They are released from rest with their centres 1 m apart and move under their mutual gravitation. Show that they will collide in less than 425 s. [G = 6.67 × 10-11 N m2kg-2.]
Find the acceleration of the block : This time the frictional force F exerted on the block is given by F = µN, where N is the normal reaction and µ is a positive constant.- Find the acceleration of the block. How do the cases µ tan α differ?
Calculate spectrum use in khz per channel : Take a simplistic approach to get a rough estimate. Find the width of each RF channel and the number of voice channels per RF channel. Ignore control channels. Calculate spectrum use in kHz per channel.
Explain the relevant history of the problem : write a letter to someone related to the local issue you highlighted on the week 8 forum. You don't need to provide your return address for the assignment, but you'll need to include it if you decide to send your letter. Provide the name and maili..
Calculate the length of a quarter-wave monopole antenna : Assuming equal transmitter power applied to both of the above antennas, would there be any difference in the power density generated at a receiving antenna? Assume free-space propagation. Explain.
What is the least projection speed that can be used : A stuntwoman is to be fired from a cannon and projected a distance of 40 m over level ground. What is the least projection speed that can be used?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Calculate the diameter of a medium carbon steel pin in

calculate the diameter of a medium carbon steel pin in double shear subjected to a suddenly applied shearing force of

  Locate the center of gravity of the casting

A cylindrical cast-iron casting has an axial hole extending partway through the casting, as shown. Locate the center of gravity of the casting.

  Find the average velocity of flow at section b

find the average velocity of flow at section B, and the pressure difference between sections A and B.

  Determine the number of discrete frequencies from the

determine the number of discrete frequencies from the minimum to and including the maximum frequency that will appear

  Free-body and kinetic diagrams

The tractor is about to tow the plane to the right. Is it possible for the driver to cause the front wheel of the plane to lift off the ground as he accelerates the tractor? Draw the free-body and kinetic diagrams and explain algebraically (letter..

  The change in flow availability for compressor and turbine

An irreversible gas-turbine power plant has a compressor with an inlet state of 1 bar and 22°C and an outlet state of 4 bars and 470 K. The turbine has an inlet state of 4 bars and 1200 K and an exhaust state of 1 bar and 900 K. The environment is at..

  Calculate the angle between periapsis and the equatorial

consider an inertial reference frame with the center of the earth as its origin and with the x-y i-j plane in the

  What is the corresponding prototype velocity

The water velocity at a certain point along a 1:10 scale model of a dam spillway is 3 m/s. What is the corresponding prototype velocity if the model and prototype operate in accordance with Froude number similarity?

  What is the corresponding change in heat flux through the

consider a roof of a house of thickness l 20 cm thermal conductivity k 1 wm k and emittance of the external surface

  Also venous blood enters at 0 mm hg and leaves at 15 mm hg

imagine that the heart acts as a pump. blood enters the heart from the lungs at 6mm hg and leaves to the rest of the

  Calculate the maximum bending stress

A W18×71 steel beam supports a superimposed uniformly distributed load as shown. Calculate the maximum bending stress. Be sure to include the beam weight.

  Estimate the wind speed and the drag force on the roof

Assuming turbulent flow along the whole surface, estimate the wind speed and the drag force on the roof (from both upper and lower boundary layers).

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd