Find rms power when emf freq is given

Assignment Help Electrical Engineering
Reference no: EM13264445

In a circuit, the generator voltage varies in time, where the amplitude of e max= 1.2 volt and emf freq.= 0.5 Hz , which the max current is equal to the max current when the freq. of emf = 3.0 Hz, which is .00033 A. In addition, when emf freq. is 0.97 Hz, the maxI = .074 A. The inductance = 30.9 mH.

-Find the resonantfrequency
-Find "rms" Power when emf freq. =0.97Hz

Reference no: EM13264445

Questions Cloud

What is the value of a put option written on the stock : What is the value of a put option written on the stock with the same exercise price and expiration date as the call option? Round your answer to the nearest cent.
Social control-conflict resolution and social change : There are three basic functions served by the law: Social Control, Conflict Resolution and Social Change. Describe and explain how each of the four major legal systems accomplishes each of those functions.
Find the change in the helmholtz potential : A cylinder contains a piston on each side of which is one kilomole of an ideal gas. The walls of the cylinder are diathermal, What is the change in the Helmholtz potential
Calculate each projects payback period cutoff : Calculate each projects payback period cutoff. Which would you accept if Puppy's payback period cutoff is 2 years?
Find rms power when emf freq is given : In a circuit, the generator voltage varies in time, where the amplitude of e max= 1.2 volt and emf freq.= 0.5 Hz , which the max current is equal to the max current when the freq. of emf = 3.0 Hz, which is .00033 A.
Define and fully describe the natural law tradition : Natural Law was one of the earliest approaches to the study of law in society. Define and fully describe the Natural Law tradition. Explain and describe the effect of Positivism, Pragmatism and Materialism upon the Natural Law approach.
How much work is done in pushing the chest : How much power is needed to push a 85kg chest at 0.72m/s along a horizontal floor where the coefficient of friction is 0.76
Society field have proposed various definitions of the law : Scholars writing in the law and society field have proposed various definitions of the law. Identify and fully describe three of these definitions found in the works mentioned in the Vago text. What are the ethical and moral implications of each?
How to amplify an ac signal that oscillates : if the LM324 is a single supply Op Amp, how can it be used to amplify an AC signal that oscillates between a positive peak and a negative peak

Reviews

Write a Review

Electrical Engineering Questions & Answers

  What is the velocity at the end of the pipe

Seawater with a specific weight of 64.0 lbs/ft^3 is at a level of 4 feet above the centerline of the exit pipe. The tank is closed at the top and there is a pressure of 1 psig above the seawater. What is the velocity at the end of the pipe

  Write an assembly language program to turn the stepper motor

Write an assembly language program to turn the stepper motor. Start a new project. Set bits 1 to 4 of PORT P ($25A) to 1 (output direction) Do not set bits 0, and 5-7, setting these bits may produce unexpected results.

  Determine what should be the width of the microstrip line

Design a microstrip transmission line with Z0 =100 ohm that will be etched onto a sielectric substrate with er = 3 and a thickness of 4 mm. what should be the width of the microstrip line

  Design band-pass filter consisting of an rc high-pass filter

a) Design a band-pass filter consisting of an RC high-pass filter with a cutoff frequency of 300 Hz and an RC low-pass filter with a cutoff frequency of 3400 Hz. Carefully select R and C of each filter so that one filter does not load the other

  What sources to pick to get total absorbed power

what sources to pick to get total absorbed power and total delivered power, since a,e,f, and h absorb and b,c,d,and g supply and for total they suggest a+c+d+e+c=absorbed and b+g+f=delivered

  Calculate developed torque at a full load armature current

A 600 V, dc shunt motor has armature and field resistance of 15 ohms and 600 ohms respectively. When the motor runs unloaded, the ine current is 3 A, and the speed is 1000rpm. Calculate the developed torque at a full load armature current of 50 A.

  What is the memory layout

What is the memory layout of the 16-bit value, 0x7654 in a big-endian 16-bit machine.

  Define invesitagtion of intermodulation through an amplifier

Invesitagtion of Intermodulation through an amplifier, An amplifier is designed to handle frequencies around 9 GHz. The bandwidth of the amplifier is 2 GHz with a center frequency of 9 GHz

  Calculate the voltage across capacitor c2 in a circuit

Assume all the capacitors in the circuit below were discharged prior to assembly. The capacitors, resistors, and voltage sources are then arranged as shown in the circuit below. The circuit is then allowed to stabilize.

  Define what is the peak frequency deviation of the fm signal

What is the peak frequency deviation of the FM signal and bandwidth of the FM signal? The signal is received with CNR = 30.0 dB. What is the SNR of the recovered video signal at the radio receiver output?

  Describe performance differences between an am and fm system

Describe the performance differences between an AM and FM system. Be sure toinclude parameters suchas: Power efficiency, spectral efficiency,noise immunity,and performance.

  Determine what is the built in potential of the diode

A silicon diode has a doping profile such that ND = ax3. What is the depth of the junction assuming the p side is uniformly doped with NA per cubic cm. Assume the x origin is at an ideal ohmic contact on the n side of the diode.(assume T=300K).

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd