Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
To analyze electric circuits, it is often necessary to solve simultaneous equations. To find the voltages Va, Vb, and Vc at nodes a, b, and c, the equations are2(Va-Vb) + 5(Va-Vc) - e^(-t) =02(Vb-Vc) + 2Vb + 3(Vb-Vc) =0Vc = 2sin(t)Find out how to use the solve function to solve for Va, Vb, and Vc so that the solution will be returned in terms of t.
The solution to Power Factor, Two single-phase loads are connected in parallel across a 415 V, 50 Hz supply. One load is rated 130 kW at a power factor of 0.75
First draw the transmit con-stellation and the receive constellation with ideal phase tracking and sampling. Note:they are obviously the same constellations. Now, assume that receiver synchronization is off by a phase angle.
Assume that a receiver has a first amplifier stage with a 5KW input resistance, a gain of 300, an input audio signal of 20 mV, and an operating temperature of 27oC. When the amplifier is operating with a bandwidth first of 10 MHz,
a. Sketch the spectrum of the original signal and the sampled signal from 0 kHz and 25 kHz. b. Sketch the recovered analog signal spectrum if an ideal lowpass filter with a cutoff frequency of 4 kHz is used to filter the sampled signal.
A series-resonant RLC circuit has R = 80 ?, L=25mh, and C=10pF. A) Sketch and label the circuit. B) Find fo, the resonant frequency. C) At what frequency is impedance a minimum D) What is the magnitude of the impedance at this frequency
A) Compare and contrast the following serial bus architectures: I2C, CAN, UART. Discuss the hardware implementation, communication protocol, and typical applications of each. B) Explain the concept of bit dominance used in CAN bus.
Consider an RLC circuit with R = 5 Ohms, L= ½ H, C= 2/9 F and input voltage e(t) = exp(-t/2)a. Starting from KVL show that the DE for the voltage across R is given by: v'' + 10 v' + 9 v = -5 exp(-0.5 t) b. Find vc in terms of the arbitrary constants ..
the SABER instrument aboard the TIMED satellite orbits the earth in a sun-synchronous polar orbit 625 Km above the earth. each of the 10 SABER focal plan detectors is 0.14mm high by 2.0mm wide. the focal plane array is 4.882*4.882mm in size
The SV curve can be used to understand the impact of constant power factor shunt compensation support. In this case, the receiving end is injected with a specific amount of reactive power so that the receiving end maintains a constant load power f..
The nickel- cadmium (nicad) battery is a secondary battery, meaning it can be recharged. it has the following reactions occuring during discharge: A nicad battery has .87 g of cadmium, which is the limiting reactant.
Indicate the use of each memory in the microcontroller (HCS12). In other words, state which one is used for code, program variables, and variables that must remain when the power is turned off.
Power Dissipation Problems, A signal generator outputs a sine wave signal with a frequency of 1000 Hz and an rms voltage of 20.0 V. The output of the spectrum analyzer is connected to a 200 ohm resistor.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd