User Account

All Pages

Find its capacitance of a capacitor

Assignment Help Electrical Engineering
Reference no: EM13961683

1) A capacitor has a charge of 0.002C when it is connected across a 100V battery, Find its capacitance.

2) A capacitor has a capacitance of 6.40uF. How much charge must be removed to lower the potential difference of its plate by 50.0V?

3) The plates of a parallel-plate capacitor have areas of 40cm2 and are separated by 0.2mm of waxed paper (K=2.2). Find its capacitance.

Reference no: EM13961683

Questions Cloud

How are the company''s assets classified : What were the companies total current liabilities at the end of the previous annual reporting period?
Write the lp model for problem : Write the LP model for this problem (mathematically define all decision variables, parameters, constrains, and objective function necessary for formulating the LP model whose solution will tell Airco how it can achieve its objective).
Case study - the case of powell vs alabama : Case Study: The case of Powell v. Alabama (1932), Using your text and the internet, in narrative format with a minimum of 500 words, outline the case of Powell v. Alabama. Give the facts, issue, and court holding of the case
When does a fund need to register with the sec : Under current U.S. laws, when does a fund (and its advisers) need to register with the SEC?
Find its capacitance of a capacitor : The plates of a parallel-plate capacitor have areas of 40cm2 and are separated by 0.2mm of waxed paper (K=2.2). Find its capacitance.
Describe the key characteristics and benefits of hedge funds : Describe the key characteristics and benefits of hedge funds.
Find the frequency of oscillation about the pivot : A straight uniform stick having a length b (m) and a mass M (kg) is freely pivoted at one end. Find the frequency of oscillation about the pivot, assuming the angle theta is small.
Determining the barrel yield and per barrel cost : Incoming crude can be processed by one of three methods. The per barrel yield and per barrel cost of each processing method are shown in the following table.
How it possible for a small force to produce a large torque : Explain (a) how it is possible for a large force to produce only a small or even zero, torque, and (b) how it is possible for a small force to produce a large torque.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  How many simultaneous users may be supported for less ber

In a DSSS multiple user system, how many simultaneous users may be supported such that an average BER of less than 10E-3 is maintained for each user if the average Eb/No=10dB, and a Pg from a straight code of 11 bit shift register length or the Np..

  Design a combinational circuit with four inputs

Design a combinational circuit with four inputs, x,y,w, and z, and four outputs: A, B, C, and D. When the binary input value in decimal is 3,8,12 or 15, the binary output value is one less than the input value, otherwise it is one greater than the..

  Determine what is the resonant frequency of the circuit

A series RLC circuit has elements with the following values: R=10Ω, L= .5H, and C=2μF. What is the resonant frequency of this circuit

  Determine input admittance yin and swr into waveguide

Slots in the broad wall of a rectangular waveguide scatter power symmetrically, so that they can be modeled as a shunt admittance,Y, in a transmission line. Consider the waveguide structure below, with four equally space slots .68 lambda apart

  Give appropriate analog signal conditioning to interface adc

A calibrated RTD with alpha = 0. 0041 / degree C, R = 306. 5 ohm at 20 degree C, and PD = 30 mW / degree C will be used to measure a critical reaction temperature. Temperature must be measured between 50 degree and 100 degree C.

  Calculate the bandwidth of the closed-loop transfer function

In a unity feedback system, the open-loop transfer function is of the form G_ol(s)=k/(1+s/Omega_p) Calculate the bandwidth of the closed-loop transfer function. How does the bandwidth depend on k and Omega_p

  Design a full wave bridge rectifier as a dc power supply

Design a full wave (Bridge) rectifier as a dc power supply that provides a peak dc output voltage of 15V on which maxiumum of 5% ripple is allowed. The rectifier feeds a load of 200Ω. The rectifier is fed from the line voltage (120V rms, 60 Hz) th..

  What is statistical process control and quality control

Give five examples of things that are measured in semiconductor manufacturing to help maintain quality. Explain how a prober can give a false reading. How is sort different than E-test.

  Determining the horizontal and vertical components

A foot valve for a pneumatic system is hinged at B. Knowing that a = 28°, determine the moment of the 4-lb force about point B by resolving the force into horizontal and vertical components.

  What are the two extreme patterns for the leds

Paste a picture of the LEDs. As you turn the dial for the potentiometer what are the two extreme patterns for the LEDs

  Find b1 and angle that b1 makes with normal to interface

a) Assume B1 = ax2 - ay10(mT), find B2 and the angle that B2 makes with the interface. b) Assume B2 = ax10 +ay2(mT), find B1 and the angle that B1 makes with the normal to the interface.

  Calculate metallurgical junction depths for the conditions

The surface concentration is fixed at N0=1.8e20/cm^2 when diffusing boron into a uniformly doped n-type substrate. The atomic diffusion constant for boron in Si at the temperature of 950 C is 3.0e-15 cm^2/s.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd