Find group delay between the highest modes

Assignment Help Electrical Engineering
Reference no: EM13249321

Parallel plate waveguide has plate seperation of 2cm, filled with dielectric material with an index refration of n=3, lenght of wavelengh guide z=50m opertaing at 10 Ghz.

a) find the cutoff frequency

b) find number of modes

c) find group delay between the highest modes and the TEM mode.

Reference no: EM13249321

Questions Cloud

Find dipole moment of the molecule : A molecule is represented by a charge -2q at the origin and charges +q at b1 and b2, where | b1 | = | b2 | = b, Find dipole moment of the molecule
What is the vswr on the line is measured : The unknown input impedance of a horn antenna operated at a frequency of 300MHz is measured using a slotted transmission line and a Smith Chart. When the antenna is connected to the slotted line, the VSWR on the line is measured to be 4
Find the output voltage and input current : A transformer has 350 primary turns and 1390 secondary turns. The input voltage is 120?V and the output current is 18.0A, find the output voltage and input current
Define what assumption is made about the origin of the argon : A 269 mg sample of rock was found to have 2.45 × 10-6 mol of potassium-40 (t1/2 = 1.3 × 109 yr) and 2.45 × 10-6 mol of argon-40. How old was the rock? What assumption is made about the origin of the argon-40?. Enter your answer in scientific notat..
Find group delay between the highest modes : Parallel plate waveguide has plate seperation of 2cm, filled with dielectric material with an index refration of n=3, lenght of wavelengh guide z=50m opertaing at 10 Ghz. a) find the cutoff frequency
Determine the stopping distance : A 2200 kg car is moving at a speed of 30.0 m/s. Determine the stopping distance (in meters) if the brakes supply a force of 3500 newtons
What is meant by high-performance organizations : Define what is meant by High-Performance Organizations (HPOs) and describe them in terms of their five key components. How are these different from more traditional organizations?
Explain the molarity of c6h12o6 in an aqueous solution : What is the molarity of C6H12O6 in an aqueous solution that is prepared by dissolving a 20.95 g sample of impure C6H12O6 in water to make 1,450 mL of solution. Assume that the sample is 93% C6H12O6 by mass. Enter your answer in mol/L, accurate to ..
What is the output snr of matched filter : if Eb the energy per bit of a binary digital signal, is 10^-5 watt-sec and the one sided power spectral density of the white noise ,N0= 10^-6w/hz then what is the o/p SNR of matched filter.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  What is the maximum frequency that an input

An OpAMP has a unity gain frequency (ft) of 10MHz and a slew rate of 10V/us and AVoc = 120dB at DC (f=0).  Assume VCC = -VEE = 15 Volts.a. Approximate the cutoff frequency of the OPAMP itself. b.

  Determine what is the output power in watts

A given device has been determined that it attenuates 4.8dB in power from its input terminal to its output terminal. What is the output power in watts if a 150-W input has been launched into a system that has two of this type of devices

  Find expressions for p and q from complex power

Let a series R-L-C network be connected to a source voltage V, drawing a current I. a) In terms of the load impedance Z=Z at angle of Z, find expressions for P and Q from complex power considerations.

  Determine the efficiency of the transformer

A 23-kVA, 2300/230-V, 60-Hz, step-down transformer has the following resistance and leakage-reactance values: R1 = 4 ohm, R2 = 0.04 ohm, Xl = 12 ohm, and X2 = 0.12 ohm. The transformer is operating at 75% of its rated load.

  Examining an rf splitter and power levels

Analysing an RF splitter and power levels, A splitter is a device that has a single input and several outputs. It is used to send a signal to several different locations

  Describe what will happen on the circuit for present state

A. Make a two bit counter with The input X =0 makes the counter count from 0-3-1-0 and X=1 goes from 0-1-2-3-0. Choose two different types of flip flops to implement it. B. Describe what will happen on your circuit when the present state is 2 and ..

  Obtain the impulse responses of the systems

(a) The ideal delay system. y[n] = x[n-nd] (b) The accumulator system. y[n] = sum (xk) , k from -inf to n (c) Forward difference system. y[n] = x[n + 1]- x[n] (d) Backward difference system. y[n] = x[n]- x[n - 1]

  Explain current pulses over a twisted pair telephone line

Current Pulses over a Twisted Pair Telephone Line, A twisted pair telephone line has a constant attenuation between 0 Hz and 3300 Hz and linear phase shift with frequency

  What would be the new pressure of the gas in psig

When the piston is at its bottom dead center, the gas is initially at 10 psig, 65°F, and 10.5 in 3 . After compression and when the piston is at top dead center, the gas is 180°F and occupies 1.5 in 3 . What would be the new pressure of the gas in..

  What are the 2nd- and 3rd-order harmonics

A recording trace r(t) is definedas r(t) = s(t) + n(t), where s(t) =10sin(20?t) (i.e., a 10 Hz sine wave, given f= 2f) is the signal and n(t) = sin(120t) (i.e., the 60 Hz electromagnetic noise) the noise.

  What distinguishes a control data value from a character

Describe the steps in the keypad polling routine. Draw a flow chart for the keypad LCD software code. Discuss challenges experienced in developing the keypad LCD software code.

  Explain plotting continuous time signal

Plotting Continuous time signal, Consider the following continuous signal: x(t) = 10e^-3t u(t) Using Matlab, plot the continuous-time signal over the range -1=

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd