Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
In actual electronic work, capacitances range from 30 picofarads, to 60 microfarads, to 5 farads. Assuming that each of these capacitances is charged to five volts, find for each a) the stored charge in coulombs, b) the number of electrons stored on one plate , and the energy in joules that is stored.
Suppose it is known that an analog signal varies between -3V and + 3V, but we require the range of this signal to be changed so that it varies from 0 to 5V in order to meet the input range of an analog/digital converter circuit.
An electric pencil sharpener is rated 240 mW, 6 V is connected to a 9-V battery and a series-dropping resistor Rx needed to power the sharpener. Calculate the value of the series-dropping resistor Rx needed to power the sharpener.
Assume a buck converter contains a synchronous rectifier. Does it operate in the discontinous conduction mode at light load Why What does the inductor current waveform look like
An infinitesimally thin metallic cylindrical shell of radius 4.00 cm is centered on the z-axis, and has an evenly distributed charge of 100 nC per meter length of shell. (a) Determine the value of the surface charge density on the conductive shell
A buck converter has an input of 6 V and an output of 1.5 V. The load resistor is 3 , the switching frequency is 400 kHz, L 5 H, and C 10 F. (a) Determine the duty ratio. (b) Determine the average, peak, and rms inductor currents.
a. The input G=0, H=0 is not allowed for this flip-flop. Why b. What is the excitation table for the GH flip-flop c. Use GH flip-flops to construct a counter to count the following sequence: 000 -> 001 -> 010 -> 100 -> 000
The wave reflects from the speeder's car and returns to the police car, where its frequency is measured to be 322 Hz less than the emitted frequency. Calculate the speeder's speed with respect to the ground.
What is the minimum sampling rate that can be used to obtain samples that completely specify the following signalx(t) = 10cos(20*pi*t) - 5cos(100*pi*t) + 20cos(400*pi*t)
The system works as follows. When the main program starts to run, the microprocessor commands the A/D to convert. The microprocessor then sits in a dummy loop until the A/D interrupts, after it has completed the conversion and data is available.
Suppose that a family of logic gates considers the input ranges of [0 - 0.2V] as "0" and [3.1V-3.5V] as "1". 1. What are the reasonable output ranges for "0" and "1" (a) "0": [0.0 - 0.1V], "1": [3.2V - 3.5V];
The next step is to construct the 32-bit ALU by wiring EIGHT 4-bit ALU blocks. The final overflow output of the 32-bit ALU is the overflow output from the most significant 4-bit ALU block. You also need a behavioral VHDL block for generating the f..
Write an algebraic expression for S3, the forth sum bit of a binary adder, as a function of inputs x0, x1, x2, x3, y0, y1, y2, and y,3. Assume that c0=0, and do not attempt to "multiply out" or minimize the expression.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd