Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
A source follower is required to connect a high-resistance source to a load whose resistance is nominally 2 kΩ but can be as low as 1 kΩ and as high as 3 kΩ. What is the maximum output resistance that the source follower must have if the output voltage is to remain within ±20% of nominal value? If the MOSFET has kn = 16 mA/V2, at what current ID must it be biased? At what overdrive voltage is the MOSFET operating?
write an 8051 program that would generate a 200khz, 50% duty cycle, square wave at P1.0.Use Timer 0 for the delay. Ignore the overheads cycles due to the instructions in the loop. Assume 12 MHz clock. All data must be hex.
A four-bit binary number is represented as A3A2A1A0, where A3, A2, A1, and A0 represent the individual bits and A0 is equal to the LSB. Design a logic circuit that will produce HIGH output whenever the binary number is greater than 0010 and less t..
An ideal n+/p diode has only the quasi neutral p region of length L illuminated with light such that GL electrons/cm3-s are generated uniformly throughout the region. There is no photo-generation occurring elsewhere in the diode. Derive the curren..
A steel tire, 10 mm thick, 80 mm wide, and 1500.0 mm inside diameter, is heated and shrunk onto a steel wheel 1500.5 mm in diameter. If the coefficient of static friction is 0.30, what torque is required to twist the tire relative to the wheel
A certain transistor is to be operated at a collector current of 50mA. How high can VCE go without exceeding a PD(MAX) of 1.2W?
Write the theoretical Power Spectral Density for a BPSK signal with shift angle of 180 degrees, carrier of 25 kHz and bit rate of about 1 kHz that has been spread by a PN sequence with a bit rate of about 100 kHz. State it or derive it.
A system is needed to measure flow, which continuously cycles between 20 and 30 gal/min with a period of 30 sec. The required output is a voltage varying from -2.5 to +2.5 V for the cycling flow range. The sensor to be used has a transfer function..
use the method of recursion to solve the following problems: compute y[n] for n = 0,1.2, when x[n] = 0 for all n andy[-l] = 2. Compute y[n] for n = 0,1.2, when x[n] = u[n]and y[-l] = 0. Compute y[n] for n = 0,1.2, when x[n] = u[n]and y[-l] = 2.
If the MOD-8 binary counter is driven by a 10 MHz input clock with a 5% duty cycle, what is the output frequency and duty cycle of the final stage
The voltage drops across three resistors in series are measured 10V, 15V, and 25V. If the largest resistor is 47 ohms, what is the value of the smallest resistor?
Using a 500 Ohm resistance, design an RC low-pass filter that would attenuate a 120-Hz sinusoidal voltage by 20 dB with respect to the DC gain.
Audio amplifiers use transformer coupling between the final amplifier stage and a speaker to match impedances and in order to avoid having DC current of the final stage flow through the speaker coil. We wish to connect an 8 Ω speaker to an 8000 Ω ..
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd