Find an equivalent force system at point o

Assignment Help Mechanical Engineering
Reference no: EM131384077

The floor of an airplane cargo bay is shown in a horizontal position.

(a) Determine an equivalent force system at point O.

(b) Determine an equivalent force system consisting of a single force, and specify the x and z coordinates of the point where the force's line of action intersects the floor.

(c) Keeping points A-D at the locations shown, suggest a repositioning of the forces so that the location of the force system described in Part (b) is closer to point O.

1964_11dc8113-6298-41e8-adb8-a6cdcc93c9ee.png

Reference no: EM131384077

Questions Cloud

Domestic violence : The violence that takes place among people who are, or were, in a personal or intimate relationship is known as domestic violence. When referring to family violence then the term becomes broader as it is the violence that takes place between family m..
Compute the resultant couple moment : Replace the forces on the two pulleys with point forces on the pinions as shown in Fig. P4.48(b), and compute the resultant couple moment (replacement of pulley forces by bearing forces is discussed in Chapter 3 in connection with Fig. 3.9).
Give symbol and purpose of each of three standard deviation : Give the symbol and purpose of each of the three standard deviations.- Using the deviation-score method, compute S for the three sets of scores.
Discuss about the post given below : You may use several stories and heroes to complete the outline (just be sure to indicate which hero you are discussing in each step). Your explanation of each step should demonstrate where the character goes through that step in their story, about..
Find an equivalent force system at point o : Keeping points A-D at the locations shown, suggest a repositioning of the forces so that the location of the force system described in Part (b) is closer to point O.
How can an organisation that offers customer the opportunity : How can an organisation that offers customers the opportunity to buy insurance services online gain insight into the types of experiences valued by its customers? How are customers' expectations of service through the web different from their ..
Calculate the mean and standard deviation for each city : The temperatures listed are averages for March, June, September, and December. Calculate the mean and standard deviation for each city. Summarize your results in a sentence.
Quality management and customer services : Quality Management and Customer Services, Topic The Voice of the Customer, The most significant part of a business is the customer. The company' profit and success depend on the customers. The company's products and services are used by a customer on..
Find an equivalent force system at point o : In a vehicle collision reconstruction analysis, an engineer estimates the tire forces shown. Determine an equivalent force system at point O.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  What is the viscosity of the liquid

A liquid is draining from a cylindrical vessel through a tube in the bottom of the vessel. If the liquid has a specific gravity of .85 and drains out at a rate of 1 cm^3/s , what is the viscosity of the liquid?

  The convective heat-transfer coefficient for wood to still

a cold-storage room is maintained at -18degc. the internal dimensions of the room are 5 m x 5 m x 3 m high. each wall

  What is the potential difference across each capacitor

Capacitors C1=12micro Farad and C2=28microFarad are each charged to 15V , then disconnected from the battery without changing the charge on the capacitor plates. The two capacitors are then connected in parallel, with the positive plate of C1 connect..

  Sketch the schematic diagram

(a) Propose a feedback control method and sketch the schematic diagram. (b) Suggest a feedforward control method and sketch the schematic diagram.

  Injection molding machine-what is minimum clamp tonnage

The bottom of a chair (where you sit, the ‘seat’) will be injection molded by itself in a mold. Assume the chair is a disk, 24 inches in diameter and 1/10 inch thick. If the injection pressure is 1600 psi, what is the minimum clamp tonnage you need f..

  Determine the thermal efficiency for the feedwater heater

Determine the thermal efficiency for the case of one feedwater heater operating at 2.0 MPa. 2. Plot the influence of the feedwater heater pressure in terms of rise of feedwater enthalpy / maximum rise of feedwater enthalpy

  Bob is asked to design a system for heating process water

bob is asked to design a system for heating process water in a chemical plant. the system is to heat 500 gallons of

  The pump draws 20 kw of power and operates at 50 efficiency

consider a pump that moves q0.1 m3s of oil s.g. 0.8 from an open reservoir through a 10 cm diameter pipe. the pump

  Neglecting the effects of motion and gravity

The combustion gases can be modeled as air behaving as an ideal gas. There is no significant heat transfer from the boiler to its surroundings. Assuming steady state and neglecting the effects of motion and gravity, determine

  What about a scalar function of vector variables

Frame Dependent and Frame Independent A vector function of scalar variables is a frame-dependent quantity. Is a vector function of vector variables frame dependent? What about a scalar function of vector variables?

  Find the maximum shear stress at the outer surface

The pressure causes tangential and axial stresses in the outer surface of 30,000 and 20,000 psi, respectively. Determine the maximum shear stress at the outer surface.

  Find the period of the resulting oscillations

Initially the particle is released from rest at a point on the table whose distance from O is 3a. Find the period of the resulting oscillations.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd