User Account

All Pages

Find a satisfactory combination of d

Assignment Help Mechanical Engineering
Reference no: EM131377775

A tension spring used in a machine must exert an essentially static force of 135 N. It is to be wound with an initial tension of 45 N, and have a spring rate of 11.0 kN/m. Determine a satisfactory combination of D, d, N, and wire material. What is the length of the coiled section when unloaded and when the 135 N force is applied?

Reference no: EM131377775

Questions Cloud

Sketch a force–deflection diagram for the spring : Suppose the force is increased until the entire spring is compressed solid. Neatly sketch a force-deflection diagram for the spring.
Provide background information about the mission and goals : Provide background information about the agency, mission, goals, objectives, departments, and strategic plan. (Title this section Introduction.)
Explain the costs involved in the creation of the system : Describe all the necessary equipment.Explain the costs involved in the creation of the system.Describe the ongoing maintenance that will be required.Provide a workflow diagram in Visio or equivalent software to illustrate how the system will work.
Explain the major source of foreign exposure : INT 620- Provide a brief historical background on the firm you have selected. Include the nature of its products or services. Explain the major geographical exposure. Explain the major source of foreign exposure.
Find a satisfactory combination of d : Determine a satisfactory combination of D, d, N, and wire material. What is the length of the coiled section when unloaded and when the 135 N force is applied?
How to build an effective business continuity program : Discuss the how Business Continuity Planning (BCP) is different from Disaster Recovery Planning (DRP).Research and find various DRP templates for organizations. Please list a least three examples (e.g. NIST, MIT and others). Also, analyze and ar..
Determine a satisfactory combination of d : Determine a satisfactory combination of D, d, N, wire material, and free length of coiled section.
How much oil is leaking from the fryer if any : In a snack frying process, potato chips are being produced at a rate of 1000 kg/h. The chips contain 35 % oil. The frying process is using up 375 kg/h of oil. Assume that the level of oil in the fryer in constant. How much oil is leaking from the ..
Why the mean would be the best measure of sales performance : Use the mean sales for each salesperson to compare the sales volumes. Explain why the mean would be the best measure of sales performance. Under what circumstances might you choose to use the median or mode?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the angle a if structure is of minimum weight

Two bars AC and BC are connected by pins to form a structure for supporting a vertical load P at C (Figure P3.5). Determine the angle a if the structure is to be of minimum weight.

  Asuming that the disk rolls without slip and the force p

assuming that the disk rolls without slip and the force p 18 n in the positive x-directionradius of disk r 20 cmmass

  A stream of methane initially at 60 degf and 400 psia is

a stream of methane initially at 60 degf and 400 psia is compressed in a single stage compressor to 1000 psia by a

  What amount of biomass would be required

Assume a biomass heating value of 17 MJ/kg, a biomass-to-syngas thermal efficiency of 85%, and a syngas-to-electricity efficiency of 38%.

  Explain what scm can do and in what it is important that

for the development of software products the scm software configuration management process is closely followed as a way

  The chain and lever attached to the gate have negligible

a gate with a circular cross section is held close by a lever 1 m long attached to a buoyant cylinder. the cylinder is

  Determine the uncertainty of the velocity measured when the

a steady frictionless air at 100 kpa and 25 c flows in a horizontal duct that has a cross sectional flow area reduction

  It is assumed that the wire surface temperature is constant

an electrical wire having a diameter of 1.5 mm and covered with a plastic insulation thickness 2.5 mm is exposed to

  Mechanical power wasted

Disregarding heat conduction through the shaft and assuming one-dimensional heat transfer, determine (a) the rate of heat transfer to the coolant, (b) the surface temperature of the shaft, and (c) the mechanical power wasted by the viscous dissipa..

  Compute a values for p u v and d in the english engineering

the reynolds number re is a dimensionless number used in fluid mechanics and is defined as repvdu where p is the fluid

  Determine the boat speed

Starting from rest at s = 0, a boat travels in a straight line with the acceleration shown by the a-s graph. Determine the boat's speed when s = 50 ft, 100 ft, and 150 ft.

  Determine the factor of safety in operation

Determine the factor of safety in operation and the angle of twist per metre length.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd