Express the corresponding force on point b as a vector

Assignment Help Mechanical Engineering
Reference no: EM131200409

The 70-m microwave transmission tower is steadied by three guy cables as shown. Cable AB carries a tension of 12 kN. Express the corresponding force on point B as a vector

260_22bbc4d9-79e2-45d6-a643-1bda20fe4453.png

Reference no: EM131200409

Questions Cloud

How much will blooper receive each month : Football coach Ira Blooper has just been fired as head coach at a large university. His buyout amount is $7.5 million, and Blooper will be repaid (as per his contract) in monthly installments over the next 4 years. If the interest rate is 1% per m..
What angle would result in a zero pressure drop : Water at 20-C ?ows through a 12-mm-diameter pipe on a downward slope so that Re ¼ 2000. What angle would result in a zero pressure drop?
The real wage of the workers in the two countries : Suppose in the United States, one worker can produce 10 tons of steel per day or 20 tons of chemicals per day. In the United Kingdom, one worker can produce 5 tons of steel per day or 15 tons of chemicals per day. The United States has 30 workers and..
What is the purpose of determine knowledge : What is adaptive learning? What is the purpose of "Determine Knowledge"? How does intellipath enhance learning? How is the intellipath grade determined? What are other important features of intellipath?
Express the corresponding force on point b as a vector : The 70-m microwave transmission tower is steadied by three guy cables as shown. Cable AB carries a tension of 12 kN. Express the corresponding force on point B as a vector
Necessary sections of business plan : You have completed all of the necessary sections of your business plan and will now create a final draft. Use any / all feedback you have received to polish your plan to the point that you could confidently show it to investors and potential partn..
The new york stock exchange is primarily : Money markets are markets for  - Foreign currency exchange, Consumer automobile loans, Corporate stocks, Long-term bonds, Short-term debt securities.
Develop an algebraic expression for the viscosity of liquid : Develop an algebraic expression for the viscosity of the liquid in the device in terms of M, g, Vm, r, R, a, and H. Evaluate the viscosity of the liquid using: M = 0.10 kg r = 25 mm R = 50 mm a = 0.20 mm H = 80 mm Vm = 30 mm/s
What is the source of power that ryan holds : Select one of these three philosophers (Rousseau, Locke, Hobbes) and write a 1-2 page paper in which you analyze the significant ways in which their ideas differ from those at work in modern democracies. What could we gain from following their ide..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  What should the revolutions per minute and horsepower output

what should the revolutions per minute and horsepower output of the prototype propeller be under dynamically similar conditions?

  Piston-cylinder device with set of stops initially

A piston-cylinder device with a set of stops initially contains 0.6 kg of steam at 1.0 MPa and 400 C. The location of the stops corresponds to 40 percent of the initial volume. Now the steam is cooled. Determine the compression work if the final stat..

  What is the pressure that the pump can deliver the

a 4 kw motor is driving an oil pump with an efficiency of 95 down a 10 mm diameter pipe. if the velocities of the fluid

  At the beginning of the compression process of an

at the beginning of the compression process of an air-standard otto cycle p1 14.7 lbin2 and t1 530degr. the maximum

  Show that the rate at which shaft work is obtained or

a. show that the rate at which shaft work is obtained or required for a reversible change of state in a closed system

  Take poissons ratio to be 291 and youngs modulus to be 307

a cubic inch of fe is subjected to a tensile stress of 25 ksi. take poissons ratio to be .291 and youngs modulus to be

  Determine the tangential force

Determine the tangential force F and the normal force N acting on the collar when u. = 45°, if the force F maintains a constant angular motion u = 2 rad>s.

  Determining the eigenvalues of the state matrix

determining the eigenvalues of the state matrix.

  Find the kinetic coefficient of friction

A metal block, placed on a rough surface, is attached to a spring and is given an initial displacement of 10 cm from its equilibrium position. It is found that the natural time period of motion is 1.0 s and that the amplitude reduces by 0.5 cm in ..

  Volume rate of flow and time required to fill mold cavity

A mold has a downsprue of length = 6.0 in. The cross-sectional area at the bottom of the sprue is 0.45 in2. The sprue leads into a horizontal runner which feeds the mold cavity, whose volume = 75 in3. Determine (a) the velocity of the molten metal fl..

  Assume that the velocity v of fall of an object depends on

assume that the velocity v of fall of an object depends on the height h through which it falls the gravity g and the

  Required results what is the rate of heat transfer q from

a copper vertical plate that is 0. 305 m tall and 1. 5 m wide separates two large air spaces. the air space at the left

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd