Explain why circuit once fabricated is unlikely to be damped

Assignment Help Electrical Engineering
Reference no: EM13278032

a critically damped parallel rlc circuit is constructed from component valures 40Ω, 8nF, and 51.2μH, respectively. verify that the circuit is indeed critically damped and then explain why the circuit once fabricated is unlikely to be trruely critically damped.

Reference no: EM13278032

Questions Cloud

What is the value of the point charge : A point charge causes an electric flux of -670 N·m2/C to pass through a spherical Gaussian surface of 18.0 cm radius centered on the charge. What is the value of the point charge
Find the magnitude of the charge on each plate : Two large metal plates of area 0.5 m2 face each other. They are 4.8 cm apart and have equal but opposite charges on their inner surfaces. what is the magnitude of the charge on each plate
Explain as a releasing heat to the surroundings : A reaction that is spontaneous can be described as a releasing heat to the surroundings. b. increasing in disorder. c.proceeding in both the forward and reverse directions.
Find what is the value of the internal resistance of the box : To the right of the circuit is an 8H (i1) and a 32H (i2) inductor in parallel. Beneath that and to the right (running up to the parallel inductors is a 3.6 H Inductor (In series). To the right of that is a wire with a switch (T=0) with the other s..
Explain why circuit once fabricated is unlikely to be damped : a critically damped parallel rlc circuit is constructed from component valures 40Ω, 8nF, and 51.2μH, respectively. verify that the circuit is indeed critically damped and then explain why the circuit once fabricated is unlikely to be trruely criti..
Expalin the enthalpy and entropy values are listed beneath : The enthalpy and entropy values are listed beneath each substance: 2 A + B ? 3 C + D ? Hf (kJ/mole) - 200 -50 -18 - 25 ? s (J/moleK) 25 40 300 75
How and why you chose your particular measures : A few years ago, the Department of Education published information about education in the United States. It reported the average amount (dollars per student) spent by public schools in each state during the prior school year.
What are the smallest instants at which these maxima occur : A voltage source Vs = 10 Cos(10^3t - 90 degrees) v, a resistanceFind the max instantaneous power delivered by the source, dissipated by R, and absorbed by L. What are the smallest instants (t > 0) at which these maxima occur.
Compute the charge on the cavity wall : An isolated conductor of arbitrary shape has a net charge of +1.1 multiply.gif 10-5 C. What is the charge on the cavity wall

Reviews

Write a Review

Electrical Engineering Questions & Answers

  What is signal to noise ratio at the output of the amplifer

Assume you have a receiver with an overall noise figure of 23 dB and a bandwidth of 1 MHz. Assuming the minimum acceptable SNR at the output of the receiver is 6 dB, estimate the minimum detectable signal level in dBm at the receiver input.

  What is the possible ouput voltage range

the CMRR of a differential votage amplifier is specified as CMRR >10³, its voltage gain is G=50. the two input voltage have values v1=10.3 and v2=10.1.

  Obtain the magnitude spectrum in one period

For the following signal x[n] = ( 1 0 n 4 0 otherwise (a) Compute its spectrum following the definition of the Fourier transform. (b) Obtain its magnitude spectrum in one period . Note: pay attention to that the magnitude must be positive.

  Calculate amount of blood that has moved through the body

If blood flows at a rate of 5 L/min for 3.5 minutes and then 4.5 L/min for 2 minutes, calculate the amount of blood that has moved through the body over the whole time period.

  Determine the voltage across each resistor

A series circuit consists of a 220V- source and 10k-ohm, 40k-ohm, and 60k-ohm resistors. Draw the circuit and find the voltage across each resistor.

  Future generation telecommunication technology

Write a report on Future Generation Telecommunication Technology.

  What is the gain of the filter at the cutoff frequency

A)Design a high-pass filter with a cutoff frequency of 40 kHz. Use 0.01 uF capacitor and an appropriate resistor. B) Sketch and label the circuit. C) What is the gain of the filter at the cutoff frequency Give your answer both as ratio (Vout/Vin) ..

  Calculate the full-load current delivered by the controller

A 92in*24in*32in, 450kg Square D motor controller is used to drive a 1600 hp,2400V,3-phase,60Hz squirrel-cage motor. a. assumeing the motor has a minimum efficiency and power factor of 96%and 90%,respectively

  Find what value capacitor should be connected in parallel

an electric motor operates at 220V rms ,60 Hz, draws 20A rms, and has a power factor of 0.75 lagging. a) what is average power absorbed by the motor b) what value capacitor should be connected in parallel with the motor to give a power factor of 1

  Calculate w in radians per second for the given

1) Calculate w in radians per second for each of the following: a. f = 30 Hz b. Period = 20 ms 2) Determine the rms values for each of the following: a. v = 100 sin wt V b. i = 8 sin 377t A

  Determine the poles and zeros of the filter

Design a filter for a biomedical instrument to eliminate DC (f = 0), 500 Hz tone, and its corresponding harmonics. The system sampling rate is 2,000 Hz. Place all the required poles at the origin to obtain a FIR filter.

  How to make adjustments if the output must be put in state

1)How do you use the Cayley-Hamilton technique to find the state transition matrix and the state equation output y 2) How do you draw the standard form simulation diagram given a higher-order differential equation

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd