User Account

All Pages

Explain the term reversibility

Assignment Help Mechanical Engineering
Reference no: EM13886219

Part - A

1) Explain the term reversibility.

2) Write the two property equations involving entropy.

3) What is meant by compressibility factor?

4) What is meant by partial molar property?

5) Define heat of reaction?

6) Explain Chemical equilibrium

7) Define degeneracy of energy?

8) What is meant by thermodynamic probability?

9) What is entropy?

10) What are applications of thermo-electric effect?

PART - B

11) What are the availability functions for closed systems?

12) Explain the causes of irreversibility?

13) Explain the Gibbs phase rule?

14) What is meant by fugacity and activity?

15) Define adiabatic flame temperature? How is it estimated?

16) Explain the reaction equilibrium?

17) What is meant by macro states and microstates?

Reference no: EM13886219

Questions Cloud

How is the u.s. economy different from a command economy? : How is the U.S. economy different from a command economy?
Define the term compression ratio : 1. Define the term compression ratio. 2. What are the assumptions made for air standard cycle?
Define vapour pressure : 1. Define Vapour pressure 2. What is Compressibility? 3. Define Surface Tension. 4. List the instruments works on the basis of Bernoulli's equation. 5. State the assumptions used in deriving Bernoulli's equation 6. Define Boundary layer Thickness.
What are your team recommendations : What are your team recommendations? Should there be something installed at this location? If so, which and why that choice? If not, then why not
Explain the term reversibility : 1) Explain the term reversibility. 2) Write the two property equations involving entropy. 3) What is meant by compressibility factor? 4) What is meant by partial molar property?
Is the check a bearer instrument or an order instrument : Is the check a bearer instrument or an order instrument? Did Glenn's delivery of the check to Carol constitute a valid negotiation? Why or why not? What type of instrument did Carol make after endorsing the check
Estimate the power output of the turbine : A 90% efficient turbine operates between two reservoirs connected by a 200-m length of 40-cm-diameter cast iron pipe that transports 0.8 m3=s of 20-C water. Estimate the power output of the turbine if the elevation difference between the surfaces ..
Factors considered while selecting a boiler : 1. What are the factors considered while selecting a boiler? 2. What are the various boiler mountings? 3. Define vacuum efficiency of condenser? 4. What is the effect of friction on the flow through a steam nozzle?
What is the maximum distance from the lower reservoir : An 88% ef?cient pump is used to transport 30-C water from a lower reservoir through an 8-cm-diameter galvanized iron pipe to a higher reservoir whose surface is 40 m above the surface of the lower one.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A vertical hydraulic cylinder has a 125-mm diameter piston

a vertical hydraulic cylinder has a 125-mm diameter piston with hydraulic fluid inside the cylinder and an ambient

  Calculate the volume flow rate and mass flow rate

Water at 30 degrees C flows through a horizontal pipe (1 inch inside diameter), in which the pressure drop is to be limited to 0.015 lbf/ft^2 per foot of length. This low pressure per foot is imposed by the excessively long line involved. Calculate t..

  The appropriate pumps are used for the water leaving the

consider a regenerative cycle utilizing steam as the working fluid. steam enters the turbine at 3.5 mpa 400oc and

  Determine his velocity and acceleration when he reaches b

when the motorcyclist is at a he increases his speed along the vertical circular path at the rate of a 0.3 fts2 where

  Steam leaves the turbine and the steam mass flow rate

A simple ideal rankine cycle has pressure limits of 3 MPa to 15 MPa, the quality of the steam leaves the turbine cannot be less than 0.95, the net output work rate generated by the cycle must be grater than 7.5 MW, try to determine the temperature of..

  The specimen failed due to stress rupture after 100 hours

a new high- temperautre alloy is to be used for a 3-mm diameter tensile support member for an impact-sensistive

  Frictionless slot that lies in the vertical plane

The 8-lb block slides in a frictionless slot that lies in the vertical plane. The stiffness’s of springs A and B attached to the block are kA =40 lb/ft and kB= 20 lb/ft. When the block is in position 1, spring A is compressed 0.5 ft and spring B is u..

  Determine the turbine work output

Determine (a) the turbine work output, in kJ/kg, and (b) the thermal efficiency of the cycle. Also, show the cycle on a T-s diagram with respect to saturation lines.

  Calculate the mass of vapor at the beginning and end of the

a closed and rigid tank with 1.5 m3 volume initially contains saturated vapor refrigerant 134a at 50deg c. the system

  At what pressure in the test section must the tunnel

a 110 scale model of an automobile is tested in a pressurized wind tunnel. the test is to stimulate the automobile

  What is the required impeller diameter ratio between the

a 20 mw radial flow hydraulic turbine is to be designed with a head of 70 m and a speed of 90 rpm. a geometrically

  The two flows exchange energy as they flow alongside each

a co-flowing heat exchanger receives air at 800k and 15 mpa and water at 15c and 100 kpa. the two flows exchange energy

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd