Explain the reason for spinning the rocket stage

Assignment Help Mechanical Engineering
Reference no: EM131249218

Consider the upper stage of a long narrow rocket used to transfer a satellite from a low-earth orbit to geosynchronous orbit (thus it is out of the atmosphere). Assume a small misalignment of the thrust vector FT from the center line, as shown in Figure 11.33. For large high-thrust solid rocket motors, the rockets are always spun about the long axis. Explain the reason for spinning the rocket stage.

185_a96f524b-05e8-4791-9ad0-0458679b91dd.png

Reference no: EM131249218

Questions Cloud

Review the videos of teachers teaching measurements and data : Review the three videos of teachers teaching measurements and data. Write a 250-500 word review of what you observed regarding the use of instructional steps in teaching measurement and alignment to the CCRs.
Caesarean sections were seen by a consultant : There were 3 infant deaths classed as early neonatal. 86 of the caesarean sections were seen by a consultant. Using the above information, calculate the following:
What other theories can you justify for parker and southwest : Is the contingency theory well represented in this example? What other theories can you justify for Parker and Southwest Airlines
Number of surgical operations : Based on the information below, what are the 1) post operative infection rates and 2) post operative death rates for Elvira Hospital between July and December of 2008? Number of surgical operations 1796
Explain the reason for spinning the rocket stage : Assume a small misalignment of the thrust vector FT from the center line, as shown in Figure 11.33. For large high-thrust solid rocket motors, the rockets are always spun about the long axis. Explain the reason for spinning the rocket stage.
Working for a company that promotes diversity : Juanita Perez strongly believes in working for a company that promotes diversity. She is currently enrolled with you in a graduate program with a major in human resources management, and she aspires to become a chief diversity officer (CDO) in an ..
Preparation of data for submission to one : A medical clinic discovers that its software had been discarding modifiers entered during preparation of data for submission to one of its third-party payers for reimbursement.
Describe qualitatively the expected motion : How many degrees of freedom does the system have? Select a set of scalar coordinates to describe the degrees of freedom.
Considerations managers face when planning change : Describe some of the considerations managers face when planning change.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd