User Account

All Pages

Explain static determinancy in detail

Assignment Help Electrical Engineering
Reference no: EM13961921

The attached diagrams show a rectangular plate held by joints defined by pins and links.

Which ones have:

A) Static determinancy

B) Overconstraint

C) Underconstraint

D) Overconstraint in some DoF,

619_aa.png

Reference no: EM13961921

Questions Cloud

What the probability that bob will arrive earlier than john : Bob and John are traveling from city A to city D. Bob decides to take the upper route (through B) whereas John takes the lower route, What is the probability that John will not arrive in city D within ten hours? What is the probability that Bob will..
Determining the work-force planning : Work-force planning All-Basa, Inc., produces two models of bookcases, for which relevant data are summarized as follows:
What is the net force applying to the box : Imagine a book on the horizontal surface. without motion (at rest). Gravity force pushing the book down with force 10 N, but the book is remaining on the surface without motion (at rest). What is the Net Force applying to the box?
Generate the most profit : Angela and Bob Ray keep a large garden in which they grow cabbage, tomatoes, and onions to make two kinds of relish - chow-chow and tomato. The chow-chow is made primarily of cabbage, whereas the tomato relish has more tomatoes than does the chow-..
Explain static determinancy in detail : The attached diagrams show a rectangular plate held by joints defined by pins and links.
What mass would have to be suspended : An organic pipe that is closed at one end has a length of 0.80 m. At 20 degrees Celsius, what is the distance between a node and an adjacent antinode for (a) the second harmonic and (b) third harmonic?
What is the minimal solution : Given the following linear programming problem: What is the minimal solution?
How much energy is then stored in the spring : A 300-g mass at the end of a spring oscillates with an amplitude of 7.0 cm and a frequency of 1.80 Hz. (a) Find its maximum speed and maximum acceleration. (b) What is its speed when it is 3.0 cm from its equilibrium position?
International space station : Let's say you own a company that makes bolts that are used on the International Space Station! These bolts have very specific requirements but two of the most important requirements are strength and heat resistance. NASA says that you must have a ..

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Determine the value of the resistance in terms of parameters

Show that a linear dependent current source controlled by a voltage appearing across an element in parallel with the dependent source is equivalent to a resistor. Determine the value of the resistance in terms of the parameters of the dependent so..

  Find electric field strength both inside nd outside cylinder

An infinitely long cylindrical dielectric of radius b contains charge within its volume of density ρv=aρ^2, where a is a constant. Find the electric field strength, E, both inside and outside the cylinder.

  What is the significance of the two nyquist criteria

Where (in the sequence of subsystems within a communication system) does the line encoder used? Draw a block diagram. Write a sentence or two on what is in the other boxes. What are the two broad parameters associated with an efficient line encoder..

  Obtain a set of equations relating to symmetrical components

A three phase star connected load is connected across a three phase balanced supply system. Obtain a set of equations relating to symmetrical components of theline and phase voltages.

  Calculate the slip of load with the mechanical losses

An induction motor has an efficiency of 0.80 when the load is 50 h.p. At this load , both stator copper loss and rotor copper loss are equal to the core losses . The mechanical losses are one -fourth of the no load losses . Calculate the slip.

  Calculate the saturation current

1. In the circuit shown in the Figure below, calculate the saturation current?

  Exercise on a project you have been connected

You may base this exercise on a project you have been connected with though your employment. If you do this you will have to arrange permission to do so.

  Compute and plot the ctfs coefficients ck

An aperiodic signal x(t) = 2sinc(2t) is multiplied by a periodic rectangular pulse train s(t) with fundamental frequency F0 = 4 Hz and the fundamental rectangular pulse given by p(t) =  1, 1/80  t  1/80 0, otherwise to obtain a signal xs(t) = x(t..

  Find new corrected power factor after installing shunt capa

A 2.4KV, single-phase circuit suppllies a load of 250KW at a lagging power factor, and the load current is 160A. If it is necessary to improve the power factor, determine the following: (a)The uncorrected poer factor and reactive load.

  Find a possible series rl circuit equivalent to n

With V=100V, the instantaneous power into a network N has a maximum value 1500 W and a minimum value ?247 W. (1) Find a possible series RL circuit equivalent to N. (2) Find S=P+jQ into N.

  Find the canonical pos of thefunction f using minterms

Consider the function f(x1,x2,x3,x4)= (x1 + x2 + ~x3 + x4)(~x1+ x4) a. Find the canonical POS of thefunction F using minterms. b. Derive the simplest POS expressionof F using algebraic manipulation.

  Design a circuit using the transistors and other components

Design a circuit using the transistors and other components used during the semester which provides at least 15 dB of gain. The 3dB filter points should be 100 HZ and 25 KHZ. Assume 110 Volt (AC) power supply.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd