Explain specific load and heat generated per minute

Assignment Help Mechanical Engineering
Reference no: EM13137772

Design Engineering: Find Specific Load and Heat Generated Per Minute
A load of 6400 Kg is carried by a journal rotating in a 270 mm bearing diameter and 400 mm long. Find the specific load on the bearing and the heat generated per minute in the bearing, assuming the shaft speed is 4 r/s and the coefficient of friction is 0.018.

Reference no: EM13137772

Questions Cloud

How much oxygen reacted : if you burn 51.8 g of hydrogen and produce 463g of water, how much oxygen reacted?
Random sample : Before you begin your analysis you are required to take a random sample of size 110 from the 170 cases in the file. Use the file Random_Sample_Generator-2.xls to do this
Determine which single point is most difficult : Analyze the fine points of portfolio theory and determine which single point is the most difficult for investors to understand, and then explain it in a way that your grandmother would understand
How many moles of hno3 are presen : How many moles of HNO3 are present in 35.0 mL of a 4.50 M solution of nitric acid?
Explain specific load and heat generated per minute : Design Engineering: Find Specific Load and Heat Generated Per Minute, A load of 6400 Kg is carried by a journal rotating in a 270 mm bearing diameter and 400 mm long. Find the specific load on the bearing and the heat generated per minute in the b..
What is the specific heat for the metal : It takes 51.0 J to raise the temperature of an 10.2 g piece of unknown metal from 13.0C to 25.0C. What is the specific heat for the metal
Federal acquisition regulation : For the Def. Acquisition Regulatory Council and Civilian Agency Acquisition council what is the membership and chairperson and how do they contribute to the FAR revision process?
What conclusion could you draw from here : Now, in Scenario B, we are going to borrow $4,000 debt and reduce the Equity to $6,000. Assume a 9% interest rate. Could you try to figure out the ROE. What conclusion could you draw from here?
Cash and securities comprising a sinking fund : The cash and securities comprising a sinking fund established to redeem bonds at maturity in 2015 should be classified on the balance sheet as:

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  A pitching wedge a golfer is using gives the ball a initial

A pitching wedge a golfer is using gives the ball a initial angle of 50 degrees, what range of velocities (Vo) will cause the ball to land within 3 ft of the hole?

  Use of waste heat and renewable heat sources

Energy in the home, personal energy use and home energy efficiency and Efficient use of ‘waste' heat and renewable heat sources

  Determine fourier number compare two identical steel spheres

Determine Fourier Number, Compare two identical steel spheres, except the first has a two inch diameter while the second sphere has a four inch diameter. The larger sphere will have a Fourier number approximately

  Explain the temperature of the refrigerant

Find the Temperature of the Refrigerant, A closed vessel with a volume of 2 ft^3 contains 5 lb of Refrigerant 134a. A pressure sensor in the tank wall reads 71.39 lbf/in.^2 (gage).

  The mean diameter of a conical friction clutch

The mean diameter of a conical friction clutch is 250mm with a width of the conical surface being 50mm. The clutch is lined with a material having a coefficient of friction of 0.25

  How to create a directory called class

make a text file that contains what is your absolute path, and call it paths.txt

  Derive the material index for a light flywheel

Roll out a sheet of blu-tack, punch out a disk with your specified radius, assemble a flywheel for testing on an electric drill and determine the approximate critical rotation speed in rpm - SEM212 T1 2014

  Calculate the surface area inside the heat exchanger

Calculate the surface area available inside the heat exchanger.

  Develop a dynamic model of a trebuchet

Analysis of the motion of swing including velocity and acceleration plots of all moving parts and projectile analysis of projectile eg: flight path, horizontal distance, deceleration and launch velocity

  Determine the minimum no of teeth required

Determine the minimum no of teeth required on pinion in order to avoid interference which is to gear with 1 a wheel to give a gear ratio of 3 to 1

  Hazen-williams formula -find the diameter of a pipe

Hazen-Williams Formula- Find the Diameter of a Pipe, The length of cast-iron pipe is to be 4200 ft., and the head causing flow is to be 12.6ft. After the pipe has been in service 5 years, it is expected to discharge water at a rate equal to 3.2 cf..

  Calculate the mass of steam in the vessel

A rigid vessel of capacity 0.6 m3 contains dry saturated steam at 4.0 bar. The vessel is cooled until the pressure is reduced to 2.0 bar, Calculate; a) the mass of steam in the vessel.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd