Explain relationship between air speed and deflection

Assignment Help Electrical Engineering
Reference no: EM13258407

The deflection of a pressure sensing diaphragm under large deflection conditions is non-linear with respect to the pressure difference across the diaphragm. using this feature to advantage, discuss how a linear relationship between air speed and deflection can be obtained from a pilot-static tube?

Reference no: EM13258407

Questions Cloud

Define what is the net ionic equation for the reaction : What is the net ionic equation for the reaction that occurs when small amounts of hydrochloric acid are added to a HOCl/NaOCl buffer solution
What is the flow rate in liters per second : Water is moving at a velocity of 1.50 m/s through a hose with an internal diameter of 1.60 cm. What is the flow rate in liters per second
Why the percentage increase in income differs : Compute the predicted 2007 operating income for Procter & Gamble and its percentage increase. Explain why the percentage increase in income differs from the percentage increase in sales.
Compute the ph of a buffer solution prepared by dissolving : Calculate the pH of a buffer solution prepared by dissolving 0.20 mole of cyanic acid (HCNO) and 0.80 mole of sodium cyanate (NaCNO) in enough water to make 1.0 liter of solution. [Ka(HCNO) = 2.0 ? 10-4]
Explain relationship between air speed and deflection : The deflection of a pressure sensing diaphragm under large deflection conditions is non-linear with respect to the pressure difference across the diaphragm. using this feature to advantage, discuss how a linear relationship between air speed
What was the inital speed of the ballwhat was the inital spe : A ball rolls across a floor with an acceleration of 1.00m/s^2 in a direction opposite to its velocity. The ball ahs a velocity of 4.00m/s, What was the inital speed of the ball
Use appendix d : What is the difference between the present value of the settlement at 5 percent and 11 percent? Compute each one separately. Use Appendix D.
The lack of opportunity to communicate : Violence is often associated with frustration born of the lack of opportunity to communicate.Self-image also includes your knowledge, experience, interests, and relationships.
Determine the liquid flow speed and the liquid pressure : At a soft drink bottling plant, a horizontal section of pipe carrying citric acid in liquid form goes from a cross-sectional area of 8.00 cm2, determine the liquid flow speed and the liquid pressure

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Determine cutoff frequency and order for anti-image filter

a dsp system is given with the following specifications: design requirements: sampling rate 20,000 Hz Maximum allowable gain variation from 0 to 4,000 Hz = 2dB 40dB rejection at the frequency of 16000 Hz

  Design a common-emitter bjt amplifier with a gain

Design a common-emitter BJT amplifier with a gain of -100 (well above 3dB point) and a 3dB point at 100Hz. Assume beta = 100, Ic (quiescent) = 1mA, Vcc=20V. You can omit the output capacitor, but should bypass your emitter resistor.

  Create a program using asmide

Create a program using AsmIDE, which utilizes the Fox 11 68HC11 microcontroller board: Speech timer where max time is 5 minutes Use the switches for:

  Determine the atomic radius of a single aluminum atom

aluminum has the FCC crystal structure. Its atomic weight is 26.98g/mole, and its density is 2.70g/cm3. Determine the atomic radius of a single aluminum atom.

  How the currents through the two transistors vary

The input of a lightly loaded transmission gate is slowly Ajit Pal, IIT Kharagpur Ajit Pal, IIT Kharagpur changes from HIGH level to LOW level. How the currents through the two transistors vary

  How to design a logic network to control the lights

A long hallway has three doors, one at each end and one in the middle. A switch is located at each door to operate the incandescent lights along the hallway. Label the switches A, B, and C. Design a logic network to control the lights.

  Calculate the s/n ratio for a receiver output

Calculate the S/N ratio for a receiver output of 4 V signal and 0.48 V noise both as a ratio and in decibel form. (69.44, 18.42dB)

  Design the lpf using blt and butterworth design technique

An ideal C/D converter is followed by a discrete-time LPF which is followed by an ideal D/C converter. The sampling rate is 8000 samples per second. The input analog signal is bandlimited to 3900 Hz. The overall frequency response is required to s..

  Find the junction temperature rise above the room temp

If the breakdown voltage increases with temperature at a rate of 40 mV/"C, find the break-down voltage of the diode at room temperature, assuming that the space-charge resistance is 10 C& independent of temperature.

  How hot would a conventional pipe have to get to burst

How hot would a conventional pipe have to get to burst and why Does it vary according to what material the pipe is made of Which are the strongest What are weak ones

  Calculate the power dissipated in the mosfet

(b) Calculate the power dissipated in the MOSFET when the lamp is operating at its rated current. (c) The maximum output current available from the logic system is 30mA. Explain why an NPN transistor would be unsuitable for this appli..

  Determine the value of the junction capacitance

The junction capacitance of a silicon pn junction is 1.83 pF at T = 300 K when the anode and cathode are held at the same voltage. The concentration of donor atoms in the n-region of the junction is 1016 cm ^-3

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd