User Account

All Pages

Examine the waveform of the reconstructed signal

Assignment Help Electrical Engineering
Reference no: EM131165148

DEPARTMENT OF ELECTRICAL AND CONTROL ENGINEERING

Objectives
1. To reconstruct the starting analog signal through filtering
2. To observe the aliasing

Instruments
• MCM30/EV Module
• Oscilloscope

Theory
The analog signal reconstruction starting from the samples is made using a low-pass filter. When the sampling frequency is equal to twice the theoretical one, an ideal low pass filter with band pass F/2, can perfectly extract the same spectrum of the starting signal.

If the sampling frequency is increased, the filtering is easier, as the repetitions of the spectrum of the signal s(t) are separated between them.

If the signal is sampled with a frequency lower than the theoretical one, or a filter with band not limited enough is used, a phenomenon occurs called aliasing.

Procedure
Signal reconstruction by filtering

• Set the circuit to PAM-1 channel mode, with flat sampling. Set SW1=flat, SW2=1CH, SW3=2; insert J2=d

• Apply 1kHZ-2Vpp to the analog input of the modulator (connect TP24 to TP1 and adjust the 2Vpp signal level)

• Connect the modulator output to the input of the 3.4 kHz low pass filter (connect TP11 with EXT IN). Set LEVEL Fl to maximum position

• Change the PAM pulse width (set SW3=1)

Exercise
i. Sketch all the waveforms.

ii. How does the reconstructed signal change?

Aliasing
• Set the circuit to PAM-1 channel mode, with flat sampling (SW1=flat, SW2=1 CH, SW3=2; J2=d)
• Connect 5kHZ to the analog input of the PAM modulator (connect TP26 to TP1)
• Connect the modulator output to the input of the 3.4 kHz filter (connect TP11 to EXT IN). turn LEVEL Fl to maximum position
• Examine the transmitted analog signal (TP4), the sampling pulses (TP6) and the PAM signal (TP11)

Exercise
i. What can you deduce from the waveforms?
ii. Examine the waveform of the reconstructed signal in TP21 and explain its shape.

Reference no: EM131165148

Questions Cloud

What is the density of the soil solids : During a shrinkage limit test on a silty clay. the volume of the dry soil pat was found to be 10.76 an' and its dry mass was 22.68 g If the shrinkage limit was 11.1. what is the density of the soil solids?
Discuss what gdp is and what it measures : Discuss what GDP is and what it measures? Discuss what the shortcomings (limitations) of GDP as a measure of well-being and welfare of a nation are?
Select a company that uses one of the structures : For each structure/model, select a company that uses one of the structures/models, and discuss the reasons why the company selected that approach based on the product or service that they market (e.g., commodity versus luxury).
How do companies develop economies of scale : How do companies develop economies of scale? Why do economies of scale often result in monopolistic or oligopolistic markets? Explain the role of government in regulating these monopolies or oligopolies?
Examine the waveform of the reconstructed signal : What can you deduce from the waveforms? -  Examine the waveform of the reconstructed signal in TP21 and explain its shape.
What role each interest group played in american politics : What is the main agenda of the two (2) groups you researched? What role has each interest group played in American politics? Provide two (2) examples for each group. How influential are these interest groups? Support your response with one (1) suppor..
Provide summary of guideline use for making stock investment : Provide summary of the guidelines used for making stock investment decisions. Your investment objective for each of your five stocks.
Calculate the expected volumetric decrease : Calculate the expected volumetric de-crease when a sample of this bentonite is dried, if its natural water content was 85%.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  What is the transfer function for the unloaded motor

What is the transfer function (steady state) for the unloaded motor?

  Determine the active power in the circuit

of resistance 5 and inductive reactance 12 is connected across a supply voltage of 526 30° volts. Determine the active power in the circuit.

  Grid-connected photovoltaic system

The objective of the project is to design a grid-connected photovoltaic system in the Atlanta area. The system is to be installed with fixed tilt and azimuth modules

  Find a complete expression for the velocity of sound in air

A 2-kHz sound wave traveling in the x-direction in air was observed to have a differential pressure p(x,t) = 10 N/m^2 at x = 0 and t = 50 μs. If the reference phase of p(x,t) is 36 degrees, find a complete expression for p(x,t). The velocity of so..

  In how many ways can a class of 30 students select committe

In how many ways can a class of 30 students select a committe from the class that consists of a president, a vice president, a treasurer, and a secretary A. if any student may serve either of these roles but no student may serve in multiple roles ..

  Determine the length of no 6 copper wire of temperature

No. 6 AWG copper wire has an area of 13.30mm2 and the resistivity at 200C is 1.75 x10-6 ohm-cm. Determine the length of No. 6 copper wireof the same temperature to give a resistance of 0.12 ohm.

  Explain how to create an array

Create an array, array1, that has the last 14 elements of which the first element is 49 and the last element is 10. THen using the colon symbol create a new array, array 2, whcih has 8 elements. the first 4 elements of array 2 are the 4th through ..

  Calculate the power in each resistor

Three resistors R1, R2 and R3 are connected in series and a supply voltage of 240 V. If R2 = 2R1, R3 = 3R1 and the total power taken by the circuit is 480 watts. Calculate the power in each resistor.

  What are some of the applications of vector and matrix norms

What are some of the applications of vector and matrix norms. Clearly explain with the aid of an example how a matrix and a vector norm can be calculated.

  Determine what is the quantization interval q

The range of an analog signal is 2 Vpp, and the samples of this signal are being quantized. The quantizer-output word size is 10 bit. What is the quantization interval Q

  Calculate initial voltage on the capacitor if v and i given

The switch in the circuit has been in position a for a long time. At t=0 the switch is moved to position b. A.Calculate the initial voltage on the capacitor if v = 200V , and i = 1.9mA.

  Describe what are the relative junction areas

Two transistors, fabricated with the same technology but having different junction areas, when operated at a base-emitter voltage of 0.72 V, have collector currents of 0.2 mA and 12 mA. Find Is for each device.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd