Evaluate the thermal conductivity of copper and constant at

Assignment Help Mechanical Engineering
Reference no: EM13604809

The temperature of a flowing gas is to be measured with a thermocouple junction and wire stretched between two legs of a sting, a wind tunnel test fixture. The junction is formed by butt-welding two wires of different material, as shown in the schematic. For wires of diameter D=125 m and a convection coefficient of h=700 W/m^2 K, determine the minimum separation distance between the two legs of the sting, L=L1+L2, to ensure that the sting temperature does not influence the junction temperature and, in turn, invalidate the gas temperature measurement. Consider two different types of thermocouple junctions consisting of (i) copper and constantan wires and (ii) chromel and aluminel wires. Evaluate the thermal conductivity of copper and constantan at T300 K. Use kCh=19 W/mK and kA=l29 W/mK for the thermal conductivities of the chromel and alumel wires, respectively.

Reference no: EM13604809

Questions Cloud

Charmaine corporation has 75880 shares of common stock : charmaine corporation has 75880 shares of common stock outstanding. it declares a 2.4 per share cash dividend on
A negative relationship between an explanatory variable x : a negative relationship between an explanatory variable x and a response variable y means that as x increases y
Two identical metal spheres a and b are connected by a : two identical metal spheres a and b are connected by a metal rod. both are initially neutral. 1.6times1012 electrons
A clinical trial is planned to compare an experimental : a clinical trial is planned to compare an experimental medication designed to lower blood pressure to a placebo. before
Evaluate the thermal conductivity of copper and constant at : the temperature of a flowing gas is to be measured with a thermocouple junction and wire stretched between two legs of
Compare the following characteristics of the two propellers : it is proposed to improve the takeoff performance of a single-engined aircraft fitted with a 50-in-diammeter propeller
Jack sawyer is presently leasing a copier from john office : jack sawyer is presently leasing a copier from john office equipment company. the lease requires 11 annual payments of
A ball is thrown from a rooftop with an initial downward : a ball is thrown from a rooftop with an initial downward velocity of magnitude vo 4.4 ms. the rooftop is a distance
What is the probability that a randomly selected teachers : the average teachers salary in noth dakota in 37764. assume a normal distribution with a population standard devation

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Air flows steadily through a constant-area duct at section

air flows steadily through a constant-area duct. at section 1 the air is at 400 kpa abs 325k and 150 ms. as a result of

  An electric motor of total weight 3330 pounds is mounted on

an electric motor of total weight 3330 pounds is mounted on a simply supported beam with an overhang as shown

  A 250 mm bar of 15mm x 30 mm rectangular cross-section

a 250 mm bar of 15mm x 30 mm rectangular cross-section consists of two aluminum layers which are 5 mm thick each brazed

  A tensile member of 2024-0 aluminum alloy used for aircraft

a tensile member of 2024-0 aluminum alloy used for aircraft fuselage had an original cross-sectional area of 4.0square

  Find the velocity of the wind

A plane can fly 299 mph in still air. If it can fly 180 miles downwind in the same amount of time it can fly 119 miles upwind, find the velocity of the wind.

  Calculate the final length and the final diameter of this

a cylinder with a 6.0 in diameter and 12.0 in length is put under compression load of 150 kips. the modulus of

  The basis of a design project which will be completed you

the basis of a design project which will be completed. you should therefore think carefully about which of the

  Advanced stress analysis assignment

Advanced Stress Analysis Assignment

  What is a 90 percent confidence interval

What is a 90 percent confidence interval for the standard deviation of the thickness of a washer produced by this procedure?

  A motorist enters a freeway at 36 kph and accelerates

a motorist enters a freeway at 36 kph and accelerates uniformly to 90 kph. from the odometer in the car the motorist

  Express the result as a cartesian vector

What is the couple moment of the two couples that act on the pipe assembly. The distance from A to B is d = 400 mm.express the result as a cartesian vector.

  Calculate the force required in direct extrusion

Calculate the force required in direct extrusion of 1100-O aluminum from a diameter of 6 in. to 2 in. Assume that the redundant work is 30% of the ideal work of deformation, and the friction work is 25% of the total work of deformation.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd