Evaluate the maximum possible efficiency actual

Assignment Help Mechanical Engineering
Reference no: EM13611297

Consider the ocean thermal energy conversion system given in the lecture notes. Also take into consideration that 30% of the gross energy output is required to move the water. a) Evaluate the maximum possible efficiency. Actual efficiencies of less than 3% can be achieved. b) Determine the thermal efficiency of the system based on the ammonia Rankine system for a 100 MW plant. Assume the pump inlet is saturated liquid and the turbine inlet is saturated vapor. Also assume the turbine is reversible and negligible pressure drop in the condenser and evaporator.

Reference no: EM13611297

Questions Cloud

Using this sample a 90 confidence interval for the : suppose that a health expert has claimed that 17 of college students smoke cigarettes. to investigate this claim
A potential difference of 600 v exists between the plates a : oppositely charged parallel plates are separated by 3.65 mm. a potential difference of 600 v exists between the plates.
Suppose you were given the task of estimating the : suppose you were given the task of estimating the proportion of drivers in troy al who text while they drive. discuss
What is the journal entry to record income tax expense and : worm company had 2007 taxable income of 60000 which included the following bad debt expense allowance for financial
Evaluate the maximum possible efficiency actual : consider the ocean thermal energy conversion system given in the lecture notes. also take into consideration that 30 of
In 2008 acme company has sales of 10000 units at10 each : in 2008 acme company has sales of 10000 units at10 each variable costs totaling 20000 and fixed costs of30000. in 2009
New equipment was purchased by tignor corporation at a list : new equipment was purchased by tignor corporation at a list price of 98000 with credit terms of 210 n30. payment was
The potential difference between the accelerating plates : the potential difference between the accelerating plates of a tv set is about 25 kv. if the distance between the plates
Company a a us company has asubsidiary located in country z : company a a us company has asubsidiary located in country z where various forms of bribery areaccepted and expected. to

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The winter indoor temperature is 23degc and the summer

a building has a peak heating load equal to 18.3 kw and a peak cooling load of 23.8 kw. estimate the seasonal heating

  Design a control system for an annealing furnace

Design a control system for an annealing furnace - Please describe any auxiliary equipment that needs to be considered. MEE 30002 Control Engineering

  If the satellite is made of material with an average

a spherical communication satellite with a diameter of 2.5m is orbiting around the earth. the outer surface of the

  The mass diffusivity of water vapor in air is 018times10-3

a desiccant is being used to remove water vapor from a stream of air with 90 rh at 50oc. the desiccant is a flat plate

  Find a the partial pressures of the air and water vapor b

a space is at a temperature of 75 f 24 c and the relative humidity is 45 percent. find a the partial pressures of the

  The pin is released which allows the piston to move

a piston held by a pin in an insulated cylinder shown in figure above right contains 2 kg water at 100c quality 98. the

  The radius of the curvature of the path of the car at b is

a 1500-kg car enter an s-curve at a with a speed of 96 kmh with brakes applied to reduce the speed to 72 kmh at a

  Calculate the diffusion co-efficient

The diffusion constant (Do) and activation energy (Q) of C in BCC Fe is 0.01 cm2/sec and 80kJ/mol respectively. In FCC Fe, the values are 0.21 cm2/sec and 148kJ/mol. At exactly 910oC these two phases can co-exist.

  Find the temperature of source and sink

a heat engine working on carnot cycle converts 25% of heat into work when the temperature of the sink is reduced by 353 k the efficiency gets doubled .find the temperature of source and sink.

  Determine the stress in ab and bc as well as the

the gap at c is initially 0.15mm before load p is applied. for p200kn the gap will close. determine the stress in ab

  What is the minimum pressure in psig

For a pump in the basement which must deliver water to a bucket on the floor of the upper mechanical room, what is the minimum pressure in psig you will see at the pump discharge.

  Calculate the force required in direct extrusion

Calculate the force required in direct extrusion of 1100-O aluminum from a diameter of 6 in. to 2 in. Assume that the redundant work is 30% of the ideal work of deformation, and the friction work is 25% of the total work of deformation.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd