Evaluate a fault with an engine management component

Assignment Help Mechanical Engineering
Reference no: EM131884859

Task sheet: Engine Management

Learning objective/task: Analyse and evaluate a fault with an engine management component.

Assignment: Analyse and evaluate a faulty Oxygen sensor.

1. You will choose a vehicle with an O2 sensor that was produced after 1998.

2. You must say what the fault is that has occurred (eg. O2 sensor voltage too high), and the DTC that would be logged.

3. You must say what the symptom of this fault would be (what would the customer notice?)

4. Show, using a diagram, how you would check the sensor. You must show what test equipment you would use AND how you would connect it to the sensor.

5. What are the correct readings you should see using the test equipment you have chosen?

6. You must say what the Engine Management System would do if this fault occurred (ie. what is the failsafe?).

7. You must say how this fault may have occurred and what can be done to make sure it doesn't happen again.

Attachment:- Assignment File.rar

Verified Expert

The paper is about the task sheet given to us in the subject of engine management. The work was related to an Oxygen sensor which is used in our work, as our subject is management, so there must be an error or mistake which we will evaluate and make corrections. There may be several reason for a fault, but in the end we have taken sufficient stage and hence the engine system is been rectified. We also have given diagnostic procedures with diagrams.

Reference no: EM131884859

Questions Cloud

Make related journal entry for the current year : In 2015 Tetra Corp generated $583,000 in revenues and incurs $276,000 In expenses. There arc no permanent or temporary book-tax differences.
How transaction would be reported on statement of cash flows : During 2014, Markowitz Company exchanged $1,700,000 of its common stock for land. Indicate how the transaction would be reported on a statement of cash flows.
What is the amount of under or over-applied overhead : During 2015, Thompson Company applied overhead using a job-order costing system at a rate of $15 per direct labor hour.
Compute the amount of gross profit to be recognized : During 2014, Nielsen company started a construction job with a contract price of 1 million six hundred and $3,000. The job was completed in 2016.
Evaluate a fault with an engine management component : Learning objective/task: Analyse and evaluate a fault with an engine management component. Analyse and evaluate a faulty Oxygen sensor
What is a notice of federal tax lien : For 2015, the maximum contribution to a qualifying deferred compensation plan by a 45-year old employee is.
Prepare the stockholder equity section of given corporation : During all of 2014, stockholders of the Planet Pluto Corporation owned 15,000 shares of its $3 par value common stock.
What is raines operating cash flow : During 2014, Raines Umbrella Corp. had sales of $742727. Cost of goods sold, administrative and selling expenses, and depreciation expenses.
Prepare the tax related journal entry for the current year : In 2015 Tetra Corp. generated $583,000 in revenue and incurs $276,000 in expense. There are no payment or temporary book-tax difference.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the principal planes and principal stresses

Knowing that the bracket AB has a uniform thickness of 5/8 in., determine the principal planes and principal stresses at point H.

  Heat is added at constant pressure until a temperature of

a cold-air standard diesel cycle has a compression ratio of 16 and begins compressing air isentropically from an

  For the wide-flange beam with loading shown determine the

for the wide-flange beam with loading shown determine the largest load p that can be applied knowing that the maximum

  Brake power and indicated power of a petrol engine

The difference between the brake power and indicated power of a petrol engine and a diesel engine

  What is the final speed of the composite particle

A particle of rest mass m0 and speed v collides with a stationary particle of mass M and sticks to it. What is the final speed of the composite particle?

  For flow over a prescribed geometry what are the

what is the coefficient of friction? the nusselt number? for flow over a prescribed geometry what are the independent

  Compute the maximum deflection in span bc of the beam

Compute the maximum deflection in span BC of the beam in Figure P7.37 and the slope on each side of the hinge.

  A crate in the back of a truck with an open tailgate has

a crate in the back of a truck with an open tailgate has impending sliding as the truck accelerates from rest to 60 mph

  A 4 lb block with an initial velocity of 5 fts is sliding

a 4 lb block with an initial velocity of 5 fts is sliding down a 30 degree slope before being slowed by a spring. if

  When being chargerd by a 40 volt dc supply find the time t

given that the instantaneous voltage across a capacitor isvc401-e-tcrvoltswhen being chargerd by a 40 volt dc supply

  Calculate the maximum load that can be raised by a force

The mean diameter of a square-threaded jackscrew is 3.00 in., the pitch is 0.40 in., and the coefficient of static friction is 0.15. Calculate the maximum load that can be raised by a force of 75 lb applied at the end of a 14-in. jack handle.

  A diesel engine uses 544 kg of fuel oilh of calorific

a diesel engine uses 54.4 kg of fuel oilh of calorific value 45 mjkg. the thermal efficiency of the engine is 25.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd